Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Dear All,
while evaluating low-power options in the context of wireless sensors, I've stumbled upon a strange behavior with the nRF52832 using ESB from SDK 14.2. Here's...
Hi
I modified the SPI master example to read an 16-bit ADC at 44.1 kHz.
While the HAL_TIMER achieves its ~22 microseconds quite good, the SPI driver is quite slow: the...
Hi!
I have an observer that listens for advertises from just one ble switch. I can control the leds on the nRF52 DK with the switch. Now i want to connect to nrf connect...
Hey guys,
I have been fighting with this for a couple of days and I am hoping someone can give me some insights as to what might be going on.
We currently use the nRF24L01P...
hi,
i am doing a project where i have to discover custom services on connected ble nodes.
i am using nrf52832 as central device and thingy 52 as peripheral device i have...
Hi Nordic:
I build up an mesh network with following setting:
1. A nRF52 platform with example/light_switch/provisioner with a auto-start-provisioner
2. Another nRF52...
Hi,
I have successfully used the nRF Connect app with a Rigado BMD-350 Dev Board to send a few UART characters back and forth to a new target device using the Rigado BMD...
I started today with the following examples to make a start with serialization:
- ..\examples\connectivity\ble_connectivity\pca10040\ser_s132_hci
- ..\examples\ble_peripheral...
HI:
I am Measuring current on custom hardware with nRF5x DK, Peak current is always too high during testing.Please give me some advice。
I am using the nRF52 DK development...
Hi,
I am working on RTC implementation. I had a doubt.. Is it possible to generate interrupts on different channels (channel 0/1/2/3) using same RTC instance ?
Thanks
Hello,
I'm trying to communicate with another device via I2C. I'm trying to do a simple write but it seems that the TWI NRFX driver is sending wrong data.
I'm just calling...
Hi,
I am implementing a beacon solution and intrested to move from fast to slow and vis versa(slow to fast) advertising modes -
i.e. BLE_ADV_MODE_FAST & BLE_ADV_MODE_SLOW...
Hey,
I have seen some articles which says that voice over BLE (4.0) is possible but there is no standard profile for it.
So far i've seen :
Silicon Labs
STM
T.I...
Hi,
After I reset nrf8001, RDY pin stays hi. I checked the crystal pin, there is no clock. I am using TSX-3225 from Epson with 12pf caps.
Am I suppose to see the clock...
Hi,
I am working on a new project with the secure bootloader (SDK 15) as a part of it. I want to add periodic task that will do several actions for example maintaining the...
