Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I'm building a software for the nrf5822 using pc10028. I'm using CMake and after following both morf.lv/modules.php and devzone.nordicsemi.com/.../ I successfully made the...
Hello Noridc,
Liking your solutions, and I appreciate the thorough documentation.
Working on layout and so I was looking carefully at your reference design Gerbers for...
Peer manager worked fine for bonding on my pca10040 board. However, when I flashed the code to my prototype, built with a SparkFun nrf52832 prototype board, I received PM_EVT_ERROR_UNEXPECTED...
Hi team,
Iam using sdk12.1.0(ble_app_beacon and ble_app_hrs_c) , i modified the advertising data and sending to other end.other end one scanner is receiving the data .but...
Hi,
i am beginner to Nordic i want to work with MMA8652FCR1 using NRF52 DK board is there any example to understand What is TWI and How to work with it. and also how i can...
Hello to all embedded Jedi Knights!
I was wondering, how could I read the CTRL-AP's APPROTECTSTATUS register (of an nrf52832) using the J-Link commander.
I know that...
What are the states of the bi-color LED (LD5) on the DK?
I'm aware that solid green is enumerated and 10Hz blinking is not enumerated (or power-only). Do the other states...
Hello,
i decided i will use a nrf52 3rd party module for my project cause i want to skip Qualification Process and Bluetooth RF-PHY test.
I haven't seen any 3rd Party...
nrf52DK - SDK12.2
This is probably a simple thing I am missing but I can't seem to find the answer.
I have been following the tutorial for BLE Characteristics ( here...
Hi,
I am working with a nrf51822 and I have seen that the way to wake up from System Off mode is by a GPIO interrupt. I wanted to know if it is needed to configure previously...
I am a new to the uVision4 and having trouble with the 51822 evaluation kit demo.
I am able to build the ble_app_hrs demo and can load and run it using the Flash / Load...
Hi
I'm using fs_storage function to read and write in flash memory. Value successfully stored in evt->store.p_data but after power off it value become 0
switch(evt-...
Hi, I'm using a nRF51822 as a observer/scanner for Eddystone beacons. This device is intended to scan up to 16 beacons, but under certain conditions (unknown at this moment...
