I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi everyone,
I'm currently developing an application supposed to read through SPI from an extrernal SRAM, i'm using nrfx_spim libraries.
Compilation is flawless but when...
Settings document explain .h_set handle will be called when the value is loaded from persisted storage with settings_load().And I want to know how it work.
I put a breakpoint...
The Bluetooth connection is disconnected, but no disconnect message is printed, and no more ads can be searched, the main thread is running fine, and the Bluetooth function...
I'm trying to just do a pristine build using the Ezurio Pinnacle 100 DVK When I originally created this project from a dev board, the resource "atmel,sam0-pinctrl.yaml" and...
Hello,
We are using the nrf52832 in SES with the softdevice s112 (v7.2.0) and sdk17.1.0 in a custom board for a BLE application (that includes OTA DFU and a custom service...
Hİ,
I can connect to LTE. but somewhere which I think it might not be the signal, it can not connect and restart (reset). not return any error. if I change my location ...
Hi there,
I have purchased a Fanstel BU840XE device ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) theres the link. The device has...
Hi,
1. How can the read slave interval be reduced to less than 2ms: twi_master_with_twis_slave
2. Test environment:
DK: pca10056
SDK:nRF5_SDK_17.1.0_ddde560\examples...
Hello,
I am aware that there is going to be an update to the BLE stack and you are soon releasing 2.8.0. For NCS 2.6.0 we were using 239354 for the host subsystem and...
Hi,
I use Nordic nRF52840 BLE Sniffer Dongle and this works as expected in Wireshark up to version 4.2.7. Hówever, when I upgrade Wireshark from 4.2.7 to 4.4.0, the Dongle...
In Software Maturity Levels under Trusted Firmware-M , it is stated that only the minimal build is supported, while the full build is still considered experimental.
In Running...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
Hi
We are using the nRF51822 with the SoftDevice S130 V2.0.1.
The nRF51 communicates with another controller via UART with a special handshake-mechanism directly on the...
I am trying to use the external flash on my NRF5340dk to store and read data files. Raw IO from the spi_flash sample seems to be working fine, but I'm not sure how to mount...
