I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi
Greetings, Hope you are doing well.
I am fairly new to using the nRF Connect SDK through VS Code. I completed the nRF Connect SDK Fundamentals course, and I also noticed...
Hi All,
I am currently working on an project with the nRF9151 using the nRF SDK v3.1.1 and MCUboot and I need to sign my application images using an external HSM. I am using...
I am having this problem in my Macbook Air M4. It times out when flashing the application via nRF Connect SDK extension. I also tried to run the nrfjprog command myself and...
I’m evaluating the nRF Connect SDK Bare Metal SDK and hit an issue with the bm_storage library. bm_storage_write() and bm_storage_read() work correctly, but bm_storage_erase...
When using GNSS periodic mode with nrf_modem_gnss_fix_interval_set() set to 20 minutes and nrf_modem_gnss_fix_retry_set() to 5 minutes, the actual wake-up intervals are inconsistent...
Hi,
I have a feeling we may be experiencing Modem Reset Loop Restrictions on some of our devices, so I want to put in something to our application code so we know and can...
Hi ,
I need to do create the bootloader . generally what we dump in to the board was the firmware not bootloader right. I want to do the OTA updates on the nRF52840 Dev...
Hello,
I am currently using nRF Cloud to perform FOTA updates on my nRF9160 devices. I have multiple certificates on this device.
1. TLS certificate for my application...
I need to store a hardware-revision value on an nRF9160 during manufacturing (using something like nrfjprog ), and the non-secure application firmware must be able to read...
Hi
I’m working with an NPM1300EK connected over I²C to an nRF54L15 , and I’m seeing an issue where the VBUSINSTATUS register consistently reads back 0x00 , even when VBUS...
Hi,
I’m working on nRF9151 with nRF Connect SDK 2.9.0 , and I’m facing a FLASH overflow issue when enabling dual-image OTA (primary + secondary partitions) . Our project...
Issue Summary
fds_record_update() in SDK 13.0.0 creates permanent duplicate records instead of replacing old records. This causes:
Valid record count to grow indefinitely...
Hi Nordic support:
Our project uses the nRF9151 and QM13545 MIPI RF SWITCH. We have a question about AT%XMIPIRFFECTRL command's frequency: If the frequency switching point...
Hello,
I encountered a very strange problem. This problem originated from my development of RGB color lights using the NRF52840. Due to the limitations of RGB color lights...
If anyone has successfully stored and retrieved settings on the nRF52840 dongle using any method, please share your approach.
I'm trying to store and retrieve settings...
