Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I want to configure the bootloader (MCUBoot on a nrf9160) to reject a new firmware image update if the new image is not suitable for the current hardware (e.g. multiple...
Hi Dev team,
I have my Thingy91 deployed and running. I wanted to know how could I locate the base station that my device is connected to. I have the information of MCC...
Hello, i'am trying to display data on my sensor Bme280 aka (temp, humidity and pression but the build is successful and the jlink is well connected the wiring is like below...
Hi,
I was using nRF Connect with all applications listed. But after installing nrfutil from git, the application all disappeared. I uninstalled nRF Connect and reinstall...
Hi, I'm attempting to use an nRF21540 to boost the range of a BLE Beacon, and I'm running into a lot of trouble getting the Eval/Dev Kit set up. First off, is there any documentation...
Is there an nRF Connect mesh sensor example. The light on/off example is great, but very simple. There is an nRF5-SDK-for-Mesh example. Are nRF5-SDK and nRF Connect compatible...
Hi to everyone,
I'm evaluating an application consisting of a bluetooth mesh where each node sends a status message to the others.
The area where the nodes will be deployed...
Hi,
We need to know the list of models (like health, configuration, lighting, sensor, generic on/off) in nCS sdk 1.7.0
can you please share inputs
thank you,
To update the Application, it is necessary to implement the update via CAN bus. Below is the hardware part, we use a CAN-SPI chip to access the bus.
We´ra using Microchip...
I would like to disable completely the 2.4Ghz radio after the 52840 has full soft device enabled and ble stack has been run.
This is after the full sequence of bluetooth...
Hi Devzone:
We put the radio test project on our custom battery powered board and encountered a problem.
When we disconnect the usb cable, the tone emitted by radio test...
Hello,
we developed the battery management system with a NRF52810.
Now the product is passing different certifications.
We need to provide info to the certification...
Hi
Trying to implement Full modem firmware update over serial port (USB) on nrf9160 in accordance with nrf\samples\nrf9160\fmfu_smp_svr in ncs version 1.5.1.
It seems...
Module: nRF52810
SDK: 14.2
Softdevice: S132 v5.1.0
Hi,
I modified the serial dfu bootloader exemple to use the SPI slave 0 instead of the UART to communicate between...
i try added Characteristic User Descriptor on nRF Connect BLE app
but on smartphone get Characteristic Extended Properties Descriptor
how can i fix this ?
