I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
hi all.
I am trying to change number of data packets in one time interval.
I don't know the senario to change it.
For first step I wrote this code to change the quee...
Hi,
I want to write data to the Flash memory of my Nordic thingy 52 board.
When I erase flash using API ret = fs_erase(&fs_config, fs_config.p_start_addr, 1, NULL); return...
Hi, I hope you are fine first of all
I'm have a PN532 module. I want to write and read data from that Midare card.
I started with the example Adafruit tag reader. when...
When i program our new nRF5340 based radio boards the program returns Device Protected for both cores on completion. It is also impossible to debug the board as my segger...
Hello
When we want to establish a pairing from the connection, I see in your examples that you call pm_handler_secure_on_connection() which calls "conn_secure()" when the...
Hi everybody,
is there an issue for using the twis
module and bluetooth at the same time?
I have problems merging the example
projects (ble_app_template and
eeprom_simulator...
Hello,
This is a strange problem and I do hope I am missing something. There are two bootloaders in the examples/dfu section for a particular transport - with debug and...
Hi,
I want to add manufacturer specific data filter in nrf_ble_scan module.
I have gone through the nRF SDK. But the manufacturer specific data filter related fields...
Hello, I want to scan all ble devices present near by nrf52-dk and process the data in my application. I am unable to find the scanning ble device code in nrf52 sdk. I am...
Shalom!
I want my code example to be able to run on both the nRF9160 and the Thingy91. I ran the SES Open nRF project menu twice and have two separate build folders under...
Comparing Current Consumption Between NRF52840 and NRF5340
Loading Zephyr HR sample code on both.
Connected to each using NRF connect and subscribed to HR UUID.
Measured...
Hi,
I understand that we have several types of sec_modes.
However, regarding modes with MITM - I don't understand how exactly those modes protect from MITM. What does...
Hello,
I started working with microcontrollers recently, I'm having issues with getting started with software development on an MS46SF11 module from Minew based on the nRF52805...
Hello. Developed with nrf52832 (S132 v7.0.1, SDK v16.0.0).
I want to get the data stored in Scan Response, but I don't know how to do it. Is there a good way to receive...
Because the GPS will continue to output data after starting, in order not to block the main thread, I placed it in another thread, but I found that when my main thread did...
