I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi all! In my example after (i guess) 3 mins with out BLE connection the system goes to sleep mode. ¿Is there any way to avoid this ? Thank you so much!
Hi,
I'm connecting with my cell-phone for the field-try test.
I want to know the modulation type when it only use the connection type??
And what the modulation type...
Hey at all,
today I wanted to set up 7 new Thingy:91 devices. All thingys are 1.4.0 // 2020.23.
So I started with updating modem FW (mfwnrf9160123) and flashing thingy91_ltem_2021...
I've modified an example project.
How do I go about exporting it, so that I can share it with other devs and they can then flash the same program onto their Development...
hello,
i am working on nrf52 dk board .NUS sdk 16
I'd like to know the start/end characteristic handle values for each service. Is the 32-bit service handle encoded as...
I have inserted the groups cluster at an endpoint. Yet, and eventhough a group seems to be additioned to the device (the device responds with 0 to the add group command from...
hi:
I need help with a problem.
Error in merge file for 52810.
use sdk:nRF5_SDK_17.0.2_d674dde
bootloader:secure_bootloader
app:ble_app_buttonless_dfu
app:FLASH_START...
Dear Nodic friends,
We use nrf52833 to design a BLE control box with USB DFU function.
During USB DFU, DFU Trigger Library will reset nrf52833, so we should connect a...
Hi
I'm trying the light lightness example, I'm using nRF Mesh Android app for provisioning. I've 2 nrf52840 DK's. One is for client and other one for server. Both of them...
Hi,
I am trying to implement BLE on nRF52840 using Zephyr APIs. I am wondering if anyone can elaborate how to use bt_gatt_write() and bt_gatt_read(). As of now, I am able...
Hi:
s132_nrf52_7.2.0_release-notes.pdf shows us below words in page 3 about limitation:
GATT:To conform to the Bluetooth Core Specification v 5.2, there shall be no secondary...
I am creating a system with one BLE central device (nRF52840 DK) and many peripherals (nRF52840 Dongles). I am attempting to create a BLE central device that interfaces with...
Hello i have a working program with ble:uart and twi in a nrf51822 device with sdk 12.3 and softdevice My system works perfectly when i use other gpio as scl and sda (external...
When I'm tuning the RF output (front end) of the nRF52832 to match 50 Ohm what state should the chip be in? Unprogrammed with power on or off? Or in receive mode with power...
Should a firmware written for nRF 52832 run smoothly on a nRF52833 if no changes in functionality are desired?
If changes to the firmware are needed, which layers must be...
