I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello Nordic, I am using
nRF5_SDK_17.0.0_9d13099,
IDE Segger V4.52c
soft device s132
Can I transfer 8208 bytes on I2C with nrf52832 with EasyDMA, ignoring the MAXCNT...
Hi,
I try to understand the power consumption of the UDP example for NRF9160 with PSM.
I'm using the default configuration: RAT="00000000", RPTAU="00100001", no eDRX,...
Hi all,
I am trying to interface a BLE mikrobus module onto a Yocto based Linux SBC. I need to use Zephyr's hci_uart example to flash it onto the module, the mikrobus...
Hi Dev Team,
I am running a program that takes in sensor data at 10 min intervals and publishes it to my server through MQTT at 1hr intervals.
I have different threads...
Hi, I am using Zephyr BLE stack to check the HCI testing og the nrf52840_pca10056 module. I am useing Windows Subsystem for Linux for Ubuntu toolchain. While using the make...
Hi,
I am planning to buy a nrf9160-DK to build a BLE LTE-M gateway. I would like to ask if the gateway is able to communicate with a private MQTT broker/server instead of...
my project is freertos+nrf52832 based the templete in SDK; A sensor pin is connect to P0.17, and I configure it low to high level trigger interrupt.In the handler I will call...
Hi all,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. I want to observe packages sent by the client and packages arriving at the server...
SDK: NCS 1.4.0
board: nRF9160-DK
sample: lwm2m_client
Question:
I am testing SERCOMM module and nRF9160-DK, but there is difference in registration procedure .
When...
Hello, I migrated codes that I believed to be relevant to the UART output to a new project, namely the uart_init function and others, and it worked in main.c, which is where...
I am trying to use the connectivity firmware with an NRF52840 dongle to communicate with an nRF52840-dk through the nordic UART service, but I am unable to use the pc_ble_py...
Hello,
I am curently working on project with a nrf9160. I will use the nrf9160 as modem controled by a nrf52840 and command AT. I will send data true GSM every 12 hours...
Hi, This is the second time posting this issue. Using nRF9160 dk with nRF Connect SDK v1.3.1 with zepyhr v2.3.0-rc1-ncs2. I tried the BME280 sample from zephyr which gives...
