I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi!
I met some issue ).
I use nrf mesh app on my phone and change it for my goals. I would like to get messages from nodes to phone via mesh. I read some posts that it...
Hi,
While developing an app which will connection to an IOS device via BLE - I've noticed an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
I understand that this event...
Hi,
I'm using NRF52840 in order to connect to a mobile device, with PIN code.
Connection to Android is ok. The issue is with IOS.
IOS can't send the PIN code to my...
Hello, We're trying to optimize the data transfer rate from our nRF52832 based peripheral device to the mobile phone. Tested with two different BLE >= 5 Android phones we...
Hello, I ve made a custom nrf52832, but ive face a lot of problemes : when logs is on the BLE is off(its not advertising) , I m not able to see it on my app. when my module...
Hello,
I am using MacBook and would like to import Keil Projects into Segger Embedded Studio by following this guide , but finally I got an error is that
I have found...
I have some questions about nRF9160.
1. What is improved comparing to revision1? Only power consumption?
2. Is GPS sensitivity improved? In revision1, it is poor.
3...
Hello!
I use light switch example in a 52DK with a 4.1.0 mesh SDK. I modified the original project and implemented the custom element model for sending arrays via mesh....
Hello.
I'm testing the integration of the BLE and TWI.
However, BLE advertising function when turn on, TWI data was not correct read.
Can you tell which one is...
Hi, I am saving data in flash memory but when I read after restarting the device it shows FF. How can I read from flash after restarting the device? and how can I check that...
Hi, i am very new to nrf family. when i use sprintf function with %d specifier, it works fine. but if i set it to %2.1f or anything with "f" included doesnt work and program...
In the ble_app_hrs_rscs_relay application, three ( NRF_SDH_BLE_TOTAL_LINK_COUNT=3) queued write modules are generated.
(one for a peripheral (server) role and two for two...
The first 0:20 sec in video -
in this 20 sec the video shows the ON / OFF switching of led .
The voltage when we click ON is 1.149 and 1.211 of warm and cool respectively...
Hi,
I am using Nordic nRF52832. I wrote the simplest code for entering system off mode. My code does nothing except system off (see below). I built the solution, downloaded...
I would like to use nRF52 DK (nRF52832) to program Fanstel BC805M EK (nRF52805) . I know that the hardware connection looks like this and we need to use the separate power...
