I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi Nordic,
I am a 52840 user, focused on keyboard pcb. I designed several keyboards using GPIOTE, matrix scanning and other techniques provided by Nordic.
However, based...
Dear All,
I have added libraries of sensor BME680 to Segger Embedded Studio (IDE) successfully. But, I need help in displaying the sensor data on Serial Monitor (Using nRF52840...
Hello,
I am in the process of porting application code from the old nRF 15.x SDK to the new zephyr based ncs 1.5.0 SDK and would like to do all hardware configurations in...
Hi Nordic Team,
We've been long waiting for FEM support with multiprotocol and it seems like it is finally here with NRF NCS v1.5.0.
1- Can you please clarify, yes I can...
Hi
I tried to add the function of FEM to the Peripheral_hids_keyboard example according to the guidance of the link below. But it looks like it failed
https://developer...
hii this is rohit vekariya from bluesys lighting solution.
i am new in nordic can you provide example code for drive neopixel(ws2812) using nrf52832
thanks
I set up nrf52832 that it is proxy device, i create a loop that proxy device sent 20 message to app phone (Android) within 100ms. But my app (Android) receive only 1 message...
I'm designing the nRF52840 into a new product with BLE, LTE and GPS.
Could you please point me to a recommended matching network and antenna solution for the nRF52840? ...
I connected a button to LED on a breadboard, how can I write a debounce function to control a button. I checked app_button.c but it seems buttons they are using is button...
Hi, We have a custom design using an nRF9160.
We can connect and program the device using a jLink though the debug port.
How can we connect the LTE link monitor to the...
Hello everyone,
I get the following error whenever I try to build an application for the thingy91_nrf9160ns board:
The secure version works just fine.
For some...
Hi Team, I have design wireless node for biomedical application. I have used nRF51822 module in my PCB. I want to see the real-stream data from sensor (connected in input...
I am getting an error like this. I did not understand what it meant. could you help me please?
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at D:\1_1_xxx_xxx_xxx\V.1.5...
HI:
I Use the Projtcet: "......\nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c".
In the BLE_Central project, how to set the Tx Power??
thank you very much...
