Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi I am the evaluation board of nRF52832 (TAIYO YUDEN Evaluation Board) EBSHSNZWZ) is used. I want to use P0.09 and P0.10 of nRF52832 as PIN of GPIO(TWI). It was set according...
Hi,
I'm developing a serialization system with nRF52832 and an application chip. My product is a power-sensitive.
The code of ble_connectivity in nRF5 SDK 17 calls nrf_drv_clock_init...
I've run into an issue with FOTA updates. The issue can be described by the following sequence of events:
A device is completely erased and programmed with a binary image...
Hi,
I am working on programming a bootloader on a NRF52840 DK using a different NRF52840 DK. Currently I have them connected via the debugger and have been successful in...
I am trying to port my build from Eclipse (based on the GCC tool chain) to a KEIL uVision build system.
I am using KEIL ARM Compiler version 6.15. Most of the files compile...
I see many similar questions to this, but I want to double check my understanding.
We have the nRF52840 connected to D-/D+ on a USB Type-C connector. We have a standalone...
Hi all!
I'm using an nRF52833, SDK 17.0.2, s140 softdevice 7.2.0. My design uses a Skyworks SKY66112 amplifier.
I have the pa_lna_assist function that I found here on...
I am running the example:
C:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10040_uart_debug\arm5_no_packs
Everything seems to be working well except...
Can you please provide security manager keypress notification sample program for bot peripheral and central program. I want to know why it is used and what is the main purpose...
Hello Nordic team
I am developing a BT mesh network project, which be implemented by nrf52840. Right now I am designing the node PCB. I want use the No.4 reference circuit...
Hi,
I tried to implement my custom service.
I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example
For SDK 15.0 it works...
I'm attempting to connect an SDcard (micro SD) to an nRF52840-DK via a breadboard setup. I'm running Zephyr and it appears that configuration is to be performed via device...
I'm trying to investigate whether I should ditch BLE in favour of Gazell and ShockBurst (to avoid the $8000 Bluetooth.com fee)
I've noticed that Gazell has no entry in the...
Hello,
I've got this Thiny:91 demo working nicely, but what I'd like to do now is only measure RSSI.
Is there firmware to only do this?
Like send AT commands only to...
Hello,
I've been trying to perform a dfu to a target Nordic device over Bluetooth using an nrf52840 dongle distributed by Laird, however whenever I attempt to run the command...
