Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have a sensor that uses 3 different BLE mechanisms. It is part of a mesh, it sometimes sends beacons and it provides GATT services in a peripheral role. The project I'm...
Hello,
Are there plans from Nordic to provide locator engine to customers? Other competitors offer this benefit, which reduces development time on the client side to create...
Hello All,
We are using NRF52840 module, need to work on serial bootloader.
I have gone through the bootloader example, our requirement is need the serial(UART) bootloader...
Hello,
How the modem selects it band of operation. Is it done automatically selected by the modem after registering to the base station? or is it assigned by the base station...
The modem firmware version 1.1.4 has been certified by Verizon, and the corresponding NCS version is v1.4.2. Now Nordic has released the NCS SDK version v1.5.0. This version...
To the kind attention of Nordic support team,
if it is not much trouble I would like to know what you consider a good/acceptable ble antenna efficiency in
desktop environment...
Hi,
I am using an nRF52832 with S132 and SDK v15.0.0 and already read in the forum about issues related to the SAADC calibration (inlcuing the erratum [86]). The problem...
Hi Nordic,
I have 2 charac i can write, let's name it A and B.
When i write into A, it trig ble_A_on_ble_evt , BLE_GATTS_EVT_WRITE , no problem.
But w hen i write...
I started developing a project on nRF52. My task is to read the value from the light sensor (phototransistor).
The sensor is connected in this way:
my code:
init...
when i Use 2.4G radio to communicate with other modules,like cc2510, i have many questins:
1. as we known that CC2510 ' modulation format of the radio signal ,MSK is only...
Hi,
Maybe this is obvious, but I couldn't find the answer anywhere online. When I power my dongle from an external 3V3 source, can I still plug it in to my computer and...
Hi, during my tests, I use an NRF52 Dongle with the nRF-Connect app as a USB/BLE interface, but now I need to handle some custom data. I have seen that the dongle uses a COM...
Hi!
I'm working on using the SAADC in 14-bit sampling mode (oversampling set to x2) using nRF SDK 17. The supply voltage for my chip is 3.3V, and I have the reference...
Hi @ all, can anyone here recommend me a suitable chip antenna, preferably one with matching regulatory documents in combination with a nRF52840 MCU.
Thanks and best regards...
