Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
I've been using the nRF52840 DK to load the firmware into my custom nRF52840 board using nRF Connect v2.6.0 and programmer v1.0.2.
However, on another laptop when I install...
Hi,
We have developed a custom board using nrf52832 chip and currently everything like (BLE, TWI, ADC etc) is working fine but we are having issues with the UART. we have...
Hi,
We are using nRF52840 with nRF5 SDK ver 16.0.0 with Softdevice S113 ver 7.0.1.
We use the radio timeslot to implement low level radio comm with very tight timing requirements...
hi i am using this to capture the adc value data_ADC=adc_buffer[1]*(1024+gain_error) / 1024 + offset_error - 0.5; data_ADC_double=data_ADC*3.6/1024; MULTIMETER MEASUREMENT...
When I used nrF52832 mouse application, the SDK version was 15.3. When I connected to MacOS, I had to make several attempts to connect. Can you tell me why?
Thank you very...
Our nRF52832-based board is powered by a coin cell battery, and spikes in current can cause the voltage to drop. This is okay early in the battery's discharge curve, but as...
The communication between the UART peripheral and the nrf52840 works fine until some device connects to the nrf device via BLE. Using a digital logic analyzer I'm able to...
hello
now we want to use nrf52840 qspi interface to connect with fpga. we have a question:whether nrf52840 could be used as qspi slave, and fpga used as master?
if it...
Hello everyone,
I am a beginner with BLE and the nRF52, so I apologize in advance if this question is pretty simplistic. Basically, I am trying to achieve the most data...
Hi, while flashing devices in production testing our customer ran into the following problem. modemFW_flash.py got stuck in an infinite loop, making no progess but consuming...
HI,
Just like discription in the ttitle. I cannot find functions (sd_ble_gap_address_set() and sd_ble_gap_address_get()) in ble_gap.h.
How can I set device address?
...
I apologize if this has been asked in a different way but I have come across several older threads that seem outdated and was hoping for the new "best practices" for the current...
Hi,I have a problem.Sometimes the program will execute to 0x08c8 during simulation on NRF52832，SDK15.2.0，Mesh3.2.I checked the map file, which is part of Softdevice.So I think...
