I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi, i am trying to add on_adv_evt in ble_app_beacon example. I modified sd_ble_gap_adv_set_configure(& m_adv_handle , &m_adv_data, &m_adv_params) to sd_ble_gap_adv_set_configure...
Hi, we are using nRF9160 and would like to save a data that is written only once(should not be overwritten or erased) and accessed every time it starts. I found that flash...
If LESC is not possible I'll settle for legacy.
I'm not able to find any document or sample code to help me get started. What i need is a pointer to document and hopefully...
Hi
I want to run the serial_uartes example for pca10040, are there any changes that i need to make in pca10056 config ? or will it work as it is in pca10056 ?
I am using...
Hi,
i am working with nRF52840-DK which i received yesterday from shipment. so i want to eun the BLE peripheral application on that.
As we know if we want to run the BLE...
I see this quote in response to a question asking for examples on how to code a scan response
possibly not - but it's trivial - just encode the scan response in the same...
Hello,
I am using SES V4.5, SDK 15.2 and the "ble_app_blinky_c" and I was not able to see the programme log.
I tried setting up the file "sdk_config.h" to use the RTT...
Hello,
I'm starting to develop an application using the DK pca10040 and SDK 15.3. At first I have just adapted peripheral ble_app_uart example and incorporated fds functionality...
Hi,
This may be a simple question, but I've gone through the infocenter and am still a little confused. I'm designing a PCB on which I'd like to have an nrf52840 that can...
Hi,
I recently purchased the nRF9160DK but cannot connect to o2's LTE-M network using the iBasis SIM, following the instructions given here: https://www.nordicsemi.com/Software...
When I trap an error in app_error.c in app_error_save_and_stop,
I mostly get a filename, line number, and an error code that I can understand.
However, sometimes I...
We are looking for a freelancer who can help to build a simple Proof of Concept of a load cell (strain gauges) ADC (HX711?) and the nRF52 development kit (810).
Objectives...
Central and peripheral is pairing and bonded. Central scanning with whitelist, if Slave is not online, master scan with whitelist will enter error when more than 30 seconds...
I'm using whitelist when bonded, but I want delete bonded then connect to anther device,.
But when scan again, whitelist_load is error. Try delete whitelist at the same...
Extended corruption occurs if DMA transfers for commands and data originate from the same RAM bank.
It is avoided if transfer of command bytes and transfer of data bytes...
