Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
Iam working on a nrf52840 and trying to achieve data flow from BLE device using NUS and transfer this data through UART.Uart is configured as (TX:P1.01,RX:P1.02).Iam...
I am using an nRF52 dev kit. I have loaded the pca_app_hts_pca10040_s132 example into the board. I only added these lines of code
nrf_gpio_cfg_output(ARDUINO_9_PIN); nrf_gpio_cfg_output...
Hi,
There are several new drivers under "nRF5_SDK_15.0.0_a53641a\components\drivers_ext\", but no example now.
I have setup the HTS221 driver and it works. I turn to...
I'm using nRF52-DK, and following the quidelines from devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader . I'm using the prebuild "blinky_pca10040...
Im trying to interface nRF52DK to Custome build acceleration sensor.
I want to use I2C communication. Are the pin connections mentioned below sufficient?
...
The buttonless_dfu_sdh_state_observer in this example is shutting down the cpu when the softdevice is disabled using an observer.
I'm not sure why this is necessary...
Hi everyone,
I have a project written in C++ for nRF52 series using the SDK 15.3.
If I use Keil and uVIsion, the project compiles and works great. With the same source...
I am using nRF52832, And SDK 15.3, the ble_app_blinky project,
a. if i have installed only the latest version of Device family 8.29.0 , when i try to build the project,...
Setup and goal: I'm developing an BLE central app and would like to use scan address filtering to find a specific device. I enabled the filter and provided a hard-coded BD...
Hello,
I successfully downloaded SAADC SDK example in the peripheral folder. The hardware setup is as below ,
The pin configuration for this is as below
...
I tried implementing
https://github.com/andenore/NordicSnippets/blob/master/examples/temp/main.c
But i get 2.6V without connecting any of the Analog pins.
Exactly...
I have attached an Arduino INO file that I wrote early on in a project. It runs a probe. It is an amazingly simple probe but especially important. I am making a simple opacity...
Hi Team,
I planning to use vibration motor with nrf52832.
vibration motor will give maximum buzz on 20.3KHz(50 duty cycle).
So my question is
- Can I achieve 20...
Hello I would like to use the extended advertinsing packets from Blutooth V5 as used in the "ble_app_rscs" example. My problem is that I can't connect via the extended advertinsing...
