Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I'm starting initial development on a new project using the nRF52832. I've been able to transmit successfully using nrf_serial_write but nrf_serial_read always returns NRF_ERROR_INVALID_STATE...
I'm working on a BLE central based on the Nordic UART Central example. The peripheral I'm talking to has a characteristic that sends an indication when written to. I'm writing...
Hello Nordic Community,
I found bsd Irrecoverable error on my other ticket
https://devzone.nordicsemi.com/f/nordic-q-a/53913/support-on-nrf9160-irrecoverable-3
I just...
Hello,
I've got a nrf52840 DK and Adafruit nrf52840 Express (less complicated then DK) i'm trying to run a PWM example from datasheet (46 PWM — Pulse width modulation...
Hello Nordic Team
I am working on SDK-v15.3. I have a requirement to update the DFU firmware in lower version too but this SDK version doesn't supporting to update lower...
i am working on a wearable device and want to develop a 1inch wearable using nrf528232 can anyone help e with minimum pcb design requirement for programming.
thanks
I am setting up the DFU example based on NRF52832.
I tried with different version of SDKs (SDK13, SDK15 and SDK16) and all based on armgcc. All toolchains are the same version...
Dear Sir,
I have implemented a program and tested it using BMD-300 Rigado DK.
The program will advertise continuously and I used nRFConnect to connect to the peripheral...
Hi, I would like to capture all bluetooth packets on a specific channel, and get their access code. Same as what Ubertooth does. Is it possible using the nRF52832? If not...
Hi,
I am trying to follow the OpenThread tutorial to build the nRF52840 NCP:
https://codelabs.developers.google.com/codelabs/openthread-hardware/#3
I installed the...
I have successfully completed my bachelor thesis project on a simple wireless sensor network using 3 nRF52 nodes and RPi with using Mqtt and Ble-6LoWPAN example from SDK....
Hi All,
We use nRF52 BLE Sniffer.Its working fiine. Please letus know, weather its possible to sniff multiple BLE devices at a time using single Sniffer. If possible, let...
Will there be an official implementation from nordic of the generic mesh models as described in the mesh model specification or are you counting on each developer to make...
How to change the Bluetooth Mesh broadcast address?
Use the sd_ble_gap_addr_set function to change the broadcast address of PB-GATT ， But PB-ADV still hasn't changed.
...
