Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello, we seem to be having an issue with LE privacy. We want to always use a random address when advertising, here is what I am seeing.
- SDK 15.3, Nrf52840.
If I disable...
Hi,
I'm working on enabling APP Protection while successfully executing below code:
if (!nrf_sdh_is_enabled()) { if (VERSION_BUILD <= MAX_RELEASE_BUILD) { NRF_UICR-...
Dear all,
I'm using and nRF51822 chip for implementing a wireless HID device with dongle.
The device has an RGB LED, and indication scenarios for different modes are played...
I'm using SDK 15.3.0 example twi_scanner with Segger Embedded Studio. I do a search entire solution for TWI_SCL_M and the only location it shows up is in main under the twi_master_init...
I'm having this issue with oldish SDK 12 but since I reproduce the issue with SDK 15: I re-used the code from https://devzone.nordicsemi.com/nordic/short-range-guides/b/software...
Hello,
I am using nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice
I am trying to interface with external Flash (MX25l64) using SPI.so when ever i am trying to send...
Hi
Any sample or known project that can transform nrf52 usb dongle and be driven through COM port?
Imagine a C program in Linux that opens the USB port where dongle...
Hi,
I'm developing a custom board based on nrf52. Currently, we are using Segger through J-Link to program nrf52 DK.
As for my custom board, I left a 2x3 pinout including...
As unicast address is a address of a element in a node.
We have to assign unicast address to 500 nodes each contains 2 elements, and we configured publish and subscribe...
Hello,
I am using nrf52832, having SDK 15.3.0 in Segger Studio IDE. Win10
I am using fds_test_find_and_delete() function, to find and delete particular record from flash...
I latest firmware and loaded and software thingy91_ltem_v0.2.2.hex. And I get reboot all the time. It was working when I first got the kit then when I was testing this weekend...
Firstly, I am a very beginner in the BLE domain. I have very little knowledge of it.
I want to do a project where multiple BLE peripheral devices(nRF52) will communicate...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
Hello,
I have the same question as mentioned in this article:
https://devzone.nordicsemi.com/f/nordic-q-a/19252/how-to-avoid-interrupt-handling-is-not-missed-with-sd_app_evt_wait...
Hi,
I use nrf sniffer to monitor BLE communication. After pairing with encryption, wireshark indicates Encrypted packet decrypted incorrectly (bad MIC).
I think there...
