I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hey Nordic Community ,
I have been trying to get the Modem firmware up and running without success for a few days now (Attempted with 2 different PCs and 2 DK with same...
hi....
i am using nrf52382 .. segger 15.2version
here i have attached two programs ble_uart and twi sensor ... its working fine but data is received over ble_uart app...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use CURVE25519.
I made my code refering to example "ble_app_multirole_lesc" and "nrf_crypto_keys.h".
NRF_CRYPTO_ECC_PRIVATE_KEY_CREATE...
Hi all,
When i walk-through the battery-service provided by nRF SDK, i note the presence of " Report Reference Descriptor " in the characteristic addition function.
I...
Hello,
I am trying to insert fds functionality to light switch client. I added all files and libraries to project. But when i try to compile project i face with errors...
When I am initializing BSD-library with bsd_init(), the function gives me back an value which i can´t find anywhere 0x00008108.
Hopefully you guys could tell me what this...
Are the virtual page sizes only allowed to be 1024 and 2048 for the nRF52840?
// This is a multiple of the physical page size. Is this allowed or not?
// <i> Expressed...
I am attempting to do the assert_tracker example. I have gotten all the code to build through Segger and upload to the DK. The problem is when I'm watching the terminal for...
Hello there,
I want to run Radio Test on one nR52832 based custom board.
I have flashed the example from SDK 15.3 on the custom board using PCA10040.
I have done the...
I am trying to use nRF9160 as ble gateway for uploading data from two nRF52832. I am wondering is it possible? can I connect nRF9160 (one gatt client) to two nRF52832 (two...
Hello,
I have the following problem. I want to create a whitelist using the PM on a manually added peer.
I manually add a peer by adding its GAP address.
Then I try...
Hello!
Like several others on here, I’m trying to make a multilink nus central firmware. My Peripheral devices run the ble_app_uart example, and the central device runs...
Hello everybody !
Here I am designing a system with 3 development boards nrf52832, where a card called "central" is connected to the computer by USB and this board will...
Dear Nordic,
I'm developing an application using the NUS service en SPIM peripheral. Both of these work correctly independently. Now I'm trying to start an SPI transaction...