Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
My environment is:
Windows 7
JLink Plus v9.3
IAR EWARM 8.30.1
SDK 15.0.0
Softdevice S132 from SDK 15.0.0
My hardware is a custom board with a Rigaldo BMD300...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hello,
I have developed my own iOS app which is capable of DFU update different devices with nRF51 and nRF52 chips.
Using only APP file (both .hex and .zip) works perfectly...
Hello,
I' trying to switch from keil uVision to Eclipse, but it doesn't work as intended. I can't debug them (hrs with and with out dfu), but the Blinky example works...
Hi,
I'm working on a custom application using two microcontrollers a pic32 and a nrf52832, I require the pic32 using an external flash memory to read the binary file stored...
I'm interesting in knowing a little more about the "address match" output of the nRF905 chip. What is the expected jitter related to the actual radio signal?
E.g. If I...
Using softdevice s132, nRF52832 on a custom board
I don't quite understand how does the SPI work exactly?
I am using it on a battery powered low power sensor application...
Hi,
We are unable to run testing with Nordic nRF52840 preview DK boaed as it is not able to be put into DTM for RF-PHY testing.
I need the hex file to flash and the...
In the nrf52 specification:
"The Phase A, Phase B, and LED signals are mapped to physical pins according to the configuration
specified in the PSEL.A, PSEL.B, and PSEL...
Hello Everyboby,
I want to know how to configure can use Public address for advertising when using nRF connect APP? Now, I just can use Random address for advertising...
Hi,
for production purposes, we need to define the components of our circuit. Less specific definitions of the parts are prefered to ensure the interchangeability of common...
Hello is it possible to send message from nrf52840 to nfr24L01, I tried (pca10056 as transmitter), program is esb_ptx_pca10056 and nrf24L01 as receiver, but could not receive...
Hi,
I would like to create a DFU package for updating an application config flash page.
We have a device where the device reads some configurations from a specific flash...
Hi Team,
Scenario-1:
There is a use-case where 8 to 10 peripheral devices need to be connected with the HUB which is based on nRF52810 and a mobile device should be...
I'm working with nRF52840 on a battery powered device , as a result theres a constraint in the total power of the cell . Now , it's been decided to use the USB2.0 at full...
