Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi everyone. I'm starting from scratch and using as reference the example/ble_peripheral/ble_app_template.
I'm using Embedded Studio 3.50 + Jlink V6.32 / The chip is nRF52832...
Hi,
I am running the BLE app uart example, using Segger Embedded Studio in Windows.
I've found that that after build and run procedure, the firmware doesn't run, as there...
I am using Master Control Panel 3.10.0.14 with 2 nRF51 Dongles. I can select a dongle and perform a Start Discovery and see devices. Next, I install Microsoft Universal Windows...
Hi
I'm facing a problem since I've upgraded to SD140 6.1 .
I'm running as multilink central, and want to keep scanning even after connection. I scan with the following...
Hi,
I am working on an application using the nrf52 sdk v15 and nrf Mesh sdk v2.1.1 on nrf52840 PDK. Starting from the nrf5_SDK_for_Mesh_v2.1.1_src\examples\sdk_coexist\ble_app_uart_coexist...
I'm currently adding a large characteristic (5.3 times bigger than my max MTU) to my device that supports multiple peripheral connections. This characteristic is used to set...
Hi.
I want to get thingy's sensor data on nRF52840.
I found that 'ble_app_multi_link_multi_role' example, but there are only get button and led state.
By using that...
The SDK for Thread v1.0.0 documentation mentions a Thread Throughput Example, but I cannot find it in the examples folder, where can I get this example app?
hi ,
I have a project with sdk14.2 nrf52832. It works well, it can broadcast, it can connect, everything is fine.
But I have a new project that requires nrf52840. My...
Hi i am trying to do DFU boot-loader in nRF52832 and i am following all the step that you have provide in nordic developer zone ( https://devzone.nordicsemi.com/b/blog/posts...
When using my mobile to make provisioning with the GATT provisioning example for the light switch, is the mobile a node? Does it get the messages as well? Does it work as...
I'm under the impression that this piece of the given example is an interrupt handler. Am I correct? If yes, then there another snippet:
So, is there a while loop inside...
Hi All,
I am facing problem in my bootloader linking please see below
Linking target: binaries/bl/bootloader.out /tmp/cc9UGLw7.ltrans4.ltrans.o: In function `nrf_svc_handler_c...