Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I am using adv_report_parse to try and return the device names the scanner picks up. However device names are being printed repeatedly.
I have 4 to 5 devices around me...
Hi
The serial connection handler "ser_conn_handlers.c" may case an INVALID_LENGTH error when receiving Advertise Reports (or other long BLE events). The reason for this...
I have BLE Nitrogen. It is defined as a disk on which it can be dropped hex and it is loaded. Please explain in detail how to make hex which can be dropped on the device....
I have code running on a nRF52 device, with SoftDevice enabled, based on the example given in this topic:
devzone.nordicsemi.com/.../
This runs fine on its own, and...
Hello !
I am currently working on a custom board on which I don't need 32.768kHz. I want to use P0_1 as an interruption pin connected to a pushbutton. The button is connected...
Hi,
I am using IAR embedded version 7.40 and my board is nRF52840 PCA10056,while i was checking devices list in IAR IDE under NordicSemi i can see only nRF51 series devices...
Hey .My source code was compiled against SDK 8.0 now we need to upgrade the SDK to 10.0.
I have just copied the SDK10.0.0"components" folder to my project ( replaced the...
main.c
y_timer.c
y_timer.h
Hi,
I wanted to make the function that get timestamp like mills().
I made this code bellow.
It does'nt move well.
Main loop is unintentionally...
Hi,
During testing I noticed rare BLE connection loses with Softdevice S110 when timeslot session is active. It is hard to catch them with sniffer due to rare behaviour....
I am trying to get the example examples/ble_peripheral/ble_app_template to work from nRF5_SDK_13.1.0.
nRF52832, s132, pca10040
Much of the code works, but inside peer_manager_init...
The device use SDK9.0,during the using of device,when disconnect the bluetooth of phone system sometimes,the system halted.
So I make an experiment about the probability...
Hello,
I am trying the Thread Cloud COAP Client
<InstallFolder>\examples\thread\experimental\cloud_coap_client
on a NRF52840 PDK. I'm using Thread SDK v0.10...
I have troubles with connection using nrf51822 and android phones:
First I connect and bond the device to the phone and it works ok.
Then I periodically...
Hiya,
Regarding voltage amplitude peak to peak for external high-swing clock HFXO 32MHz, what's supply rails？I don't find out this specification defined in datasheet PS_V1...
