I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Using Keil MDK Lite v 5.22, writing code in C for nRF52, with SDK 12.
Example code works.
How does one declare a function, define it, and call it?
I've created a...
In my debugger, I see that variable error_code is 0x00000004
void app_error_handler_bare(ret_code_t error_code)
{
error_info_t error_info =
{
.line_num = 0,
.p_file_name...
I'm running a debug session.
I set a break point inside of function services_init on line 201.
I ran the run up to break point command
The processor pauses on...
Hi,
i am trying to save data with the flash data storage module. Using this code ( infocenter.nordicsemi.com/index.jsp from infocenter erverything works fine. But when...
I am attempting to do a BLE firmware update via command line tools in an attempt to automate programming in a script file. I have zero problems performing an over the air...
In a project using esb, with two nrf52832 devices configured as default, one as RX, one as TX, with dynamic payload, TX sending packets to RX can change the packet pid (and...
Hi!
I have two PCA10040 boards and I'm running the MQTT publisher example in both using a Raspberry Pi 3 Model B as a gateway.
Therefore, both boards are establishing...
Hello,
I am using pca10028 and sdk 12.2. I am trying to run some code. I am getting some make file error as ble_nus_error.PNG .
My main.c file is New Text Document (3...
Hi,
I have 2 nRF512840 eval kits and tried out the att_mtu_throughput example provided on SDK 13.0.
The throughput about 900-1000Kbps can be achieved with PHY 2.0 DLE...
Is there any way that I can use more than 4 timer in nRF 51 ??
(four or more...)
I'm using Softdevice 130, so It uses Timer 0,
and I'm using RGB Sensor using PWM Library...
i m new in NRF52832, i use saadc exemple pca 10040 sdk 13.0.0, i dont now how to get adc result from the buffer because there is 2 elements in the buffer :
err_code = nrf_drv_saadc_buffer_convert...
Hi, Nordic Forum!
We've been trying to implement an adapted version of the Secure Bootloader with Buttonless DFU in our custom board. We have successfully accomplished...
In this app by Nordic
github.com/.../Bluefruit_LE_Connect_Android
a cyclic redundancy check (CRC) is added to the payload byte array before writing it to the UART receiving...
