Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Latest 2.7.0 toolchain.
nrf5340DK board, light_bulb example.
I am using our own smartphone to perform up to AddNOC and ThreadNetworkSetup.
Then the control is transferred...
Hi, I would like to write a log to an SD card but I am completely unable to even connect to it using SPI in Zephyr/nRF Connect SDK. There seems to be some mismatch between...
I am working in NCS v2.7.0 for nRF52833 DevKits, and trying to set up a secure BLE connection to allow remote control of the device over GATT.
My devices are headless IOT...
Hi All, I have a 5340dk and it got bricked for no reason, last night I was able to flash and debug my program. But when I tried this morning, device is behaving unexpectedly...
Hello !
You have DTM test in nRF5_SDK_17.1.0 and in nRF Connect SDK.
I have used SDK test some years ago and it looks more simple if we compare it with new environment...
Hello,
I am working with the nRF9160 to communicate via DTLS. It works, but managing certificates is a bit of a problem. I am using the AT%CMNG command.
First, certificates...
When running example code which involves BLE on nRF52840-based boards, the devices (which have assigned names in the example code) don't show up on the iOS nRF Connect scanner...
Hello,
I am using nRF Connect v2.6.0 and nrf52832 for product development.
I have implemented MCUmgr callbacks to check the DFU status, as shown in the code snippet...
I need to move everything off of UART0 so I can use it for my touchscreen
On a previous post I was told I could move everything to RTT in the overlay, but when I try to...
We've noted that our coordinator sometimes hangs and it's because that sometimes, maybe once every 1000-10000th call, the zb_zdo_mgmt_lqi_req API never responds to the callback...
We have experienced some modem faults and have implemented a custom `nrf_modem_fault_handler` to try to capture them.
We have enabled the config:
CONFIG_NRF_MODEM_LIB_ON_FAULT_APPLICATION_SPECIFIC...
Hi,
I used the reference code from inter_less8_exer3_solution and successfully built it with the nrf5340dk board. However, when building it for the nrf7002dk , I encountered...
I'm using firmware 1.3.6 and sdk 2.7 for Nordic nRF9160. For the internet connection ppp is being used.
Here are the results:
modem shell:
time wget https://leil.de...
