I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
SDK: nRF5_SDK_17.1.0_ddde560
example: secure_bootloader_ble_s132_pca10040
The example works when I use the S132, but when I replace with S312 it does not.
i have already...
Hi there,
We are currently using nRF Conenct SDK revision v2.5.0
https://github.com/nrfconnect/
Initially started with v2.6.1 but had to downgrade to v2.5.0 due to some...
I'm getting error:
When trying to use any of the time related functions: localtime,strftime etc. I have the
"#include <time.h>" in the file, but armgcc is acting like...
Hello all,
I am designing a custom board utilizing the nRF52832 QFAA. For the first version of this board, I am attempting to closely replicate the layout of the nRF52832...
Hi
I want to be able to access some build type variables in my C code in a Zephyr project (using west as the build manager) to be able to show them on a screen or in logs...
Hi,
I am working on nRF52840 DK for Bluetooth Locator Tag following guidelines as per Bluetooth Fast Pair: Locator tag (nordicsemi.com) . I am receiving following error...
We have developed a custom board based on the nRF52840-CKAA-R7.
Development is well into the re-release phase, and I am having some issues with battery life.
I've done...
Hi,
I have a mass storage that format a fat_fs volume and create a file when I plug the device by USB. Here is how I create a file :
It works fine, and I can see my...
Good morning,
I am developing my Zephyr solution with a Supported board RAK4631 in a RAKWireless solution called Wisblock. This is a kind of building blocks called Wisblock...
Hi,
I have the unfortunate task of needing to update a significant amount of inventory (several thousand units) using BLE OTA.
The devices are using the nRF52805 with...
Hello, I am currently developing a program that uses two SPI interfaces with the nRF5340DK. I want to use SPI3 and SPI4 for two different modules. SPI4 works fine and I can...
There are some fields that I wish to change. I am using the project direction_finding_connectionless_rx as a base to work with. I would like to be able to read and write specifically...
uart:~$ wifi_radio_ficr_prog otp_write_params 0x120 0xff63ec4f 0x9fff OTP Region is open for R/W Invalid MAC address. MAC address cannot be all 0's, broadcast or multicast...
I have a device on my desk that performs the data transfer I need, so I know it's possible. I've attached a screenshot of the successful data transfer.
I tried to replicate...
