Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
Since some days I try to create own applications with the nRF5440 processor. I tried it with Segger Embedded Studio and also Visual Studio Code. The example projects work...
Hi,
I have been trying out the Matter samples as shown in this webinar . I have been following the instructions for version 1.7.0 of the SDK, specifically the ones in Configuring...
Hi,
I'm implementing a simple DFU for my device. The device has the buuttonless dfu rom and bootloader. I working on my android app now.
I want to be able to read the...
Hi,
I ran some tests with the SW and HW crypto on nrf5340dk. I expected that using the crypto cell would improve my crypto performance tremendously but unfortunately,...
Dear friends,
My 52840 DK flashed a serial example( nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial ) as a provisioner.
We use PyACI communicate with provisioner by Uart...
Good evening,
Referring to the following page which lists IDEs that are supported by Nordic Nordic Supported IDEs
Please kindly let me know if the following toolchain...
Hello,
first I have to say that I'm new with nRF5340, Segger Embedded Studio and Cmake.
I have a working project with CMakeList.txt. So I include it into Segger Embedded...
Hi.
I am trying communication from nRF52832 to iPhone using ble.
I use main function which put in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart.
But,I...
Hello,
I have done the setup of Lsm5dsl with Nrf52832 DK board but I little bit confused about what hardware configuration is there so please guide me.
This is Code...
Hello Nordic great team,
We have a question please, we would like to configure our IOT device through the air, and the best way as we see in our use case, is to use the...
Hi there,
I tried to configure the openthread co-processor radio.
The build went well for my nRF52840 dongle, I managed to generate the RCP package image but when I install...
Hi!
I'm working with the nRF52833 in a Laird dev kit, the bl653_dvk and I cannot build a Hello World with mcuboot application in nrf sdk 1.7.0 or greater.
Although in...
Added the below lines to the peripheral_hr and I could see the logs without any trouble.
Same lines added to the central_and_peripheral_hr and I can see anything. What I...
Does someone have experience driving several slaves on a QSPI bus? Can we use a general IO pin for Chip Select (CS)? [Edtit] (I believe the nCS - QSPI pin described in the...
