I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I want to use BLE Direction Finding solution. However, I couldn't find any documents or any software library. Is there support in SDK for direction finding ? Are...
I request detail information about the UART internal implementation of the UART in the nRF52810 microcontroller.
Many application are used in noisy environment.
From other...
Hi
I am trying to flash the device with the bootloader, the soft device and the application, because I do not want do the OTA update at production.
I used the following...
Hi,
I want to control leds of nrf 52840 board through raspberry pi 3 B model uisng python.
I used interactive pyaci example for provisioning nrf sdk board, but it requires...
I am using NRF52840 development board with SEGGER Embedded Studio (Nordic Edition)
I downloaded example code to target board. The software run with Zephry. I found function...
I tried to follow this tutorial to set up the Connect SDK toolchain with CLion. It worked until I resetted the CMake Cache. Now it always gives me this error message.
...
Good evening,
I'm analyzing the FreeRTOS HRM example for PCA10040.
I'd like to understand the meaning of the following comment available in your code in order to prevent...
I am having a very strange problem with timers and the PPI channels.
I am trying to take a fixed number of ADC samples at 1 ms intervals starting at a fixed offset in time...
I'm trying to set up the nRF Connect SDK Toolchain on Ubuntu 20.04.2 LTS x86_64, following this manual.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.1/nrf/gs_installing...
I have plugged in the NF5340 development board into a USB port on my laptop with a USB 2 cable, but LED 1 does not light. Only the LED next to the light PCA i.c. lights -...
Hello,
I am using nRF Connect for Descktop for Windows 10 v3.6.1, and the nrf52840 Dongle.
Is it possible to scan / connect to BLE 5.0 devices (with PHY Coded) using...
Hello,
I'm working with nRF52840 dongle, i installed nRF Connect on ubunto 18.4 and i am using python3. After installling pc-ble-driver version 0.15.0 in python3 i tried...
I start the sniff and see packets from all advertising peripherals in the area. I select my peripheral in the Device dropdown list. Then I see a string of "ADV_IND" packets...
Hi there,
I've got a situation when using TWI where an ` NRF_ERROR_INVALID_ADDR` is returned having performed a call to ` nrfx_twim_tx`. I understand that this relates to...
