Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi Nordic,
I am a 52840 user, focused on keyboard pcb. I designed several keyboards using GPIOTE, matrix scanning and other techniques provided by Nordic.
However, based...
Dear All,
I have added libraries of sensor BME680 to Segger Embedded Studio (IDE) successfully. But, I need help in displaying the sensor data on Serial Monitor (Using nRF52840...
Hello,
I am in the process of porting application code from the old nRF 15.x SDK to the new zephyr based ncs 1.5.0 SDK and would like to do all hardware configurations in...
Hi Nordic Team,
We've been long waiting for FEM support with multiprotocol and it seems like it is finally here with NRF NCS v1.5.0.
1- Can you please clarify, yes I can...
Hi
I tried to add the function of FEM to the Peripheral_hids_keyboard example according to the guidance of the link below. But it looks like it failed
https://developer...
hii this is rohit vekariya from bluesys lighting solution.
i am new in nordic can you provide example code for drive neopixel(ws2812) using nrf52832
thanks
I set up nrf52832 that it is proxy device, i create a loop that proxy device sent 20 message to app phone (Android) within 100ms. But my app (Android) receive only 1 message...
I'm designing the nRF52840 into a new product with BLE, LTE and GPS.
Could you please point me to a recommended matching network and antenna solution for the nRF52840? ...
I connected a button to LED on a breadboard, how can I write a debounce function to control a button. I checked app_button.c but it seems buttons they are using is button...
Hi, We have a custom design using an nRF9160.
We can connect and program the device using a jLink though the debug port.
How can we connect the LTE link monitor to the...
Hello everyone,
I get the following error whenever I try to build an application for the thingy91_nrf9160ns board:
The secure version works just fine.
For some...
Hi Team, I have design wireless node for biomedical application. I have used nRF51822 module in my PCB. I want to see the real-stream data from sensor (connected in input...
I am getting an error like this. I did not understand what it meant. could you help me please?
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at D:\1_1_xxx_xxx_xxx\V.1.5...
HI:
I Use the Projtcet: "......\nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_uart_c".
In the BLE_Central project, how to set the Tx Power??
thank you very much...
