Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi every one,
I am using mesh in uart_app
PROJECT-------->
I am sending data through nRF UART APP to BLE (in MESH condition) and the received data on BLE sending it...
Dear Sir/mam,
Could any tell what header file I have to include to resolve this error? Please see in the screenshot
And in which I am sending data using nRF UART APP,...
Hi,
The Segger software does not work behind a proxy server.
After installing and licensing it (by moving the machine outside our corporate firewall) we try to start...
Hi all
I am using nrf52 with max30003 to read full ECG and send it over BLE.
My data is acquired at 128SPS.
De default GAP settings are too slow to receive all the needed...
Hello,
we're trying to develop central BLE application on nRF52840 using SDK 16.0.0 and S140 softdevice to connect with BLE pulseoximeter (Jumper JPD-500F - it uses TLSR8266...
From the documentation i have found it seems all the nrf52 and the new nrf5340 are all "extended range" up to 105 degrees celcius.
I am evaluating an application where a...
Hello!
Thanks for your help last time, highly appreciated.
However I haven't got till actuall programming because now I can't upload hex files. I start Thingy:91 in boot...
Hi guys,
I just started to work with Nordic boards and I am currently working with Nordic nRF52-DK. I have already installed all the necessary tools that I need to run and...
Hello,
I've been playing around with the nrf52 DK (sdk 16.0.0, s132). I'm trying to add volume up/volume down functionality to the example. I found this source code from...
Hello,
Does anyone has an example of MQTT LST application for nrf9160.
I've tried to use the MQTT_Simple sample with LST.
I've add "CONFIG_MQTT_LIB_TLS =y" change the...
Hi everyone,
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840 SOC.
The system will operate in normal voltage mode (VDD = VDDH...
Dear All,
I am trying to compile a project from the command line and I want to enable all the warnings possible for the files that I have created. I am using the NCS v1...
hi support team,
i tested the example of \\nRF5_SDK_16\examples\peripheral\usbd_msc , and SD card interface , that with the APP_SDCARD_FREQ_INIT 268435456 (1 M) and APP_SDCARD_FREQ_DATA...