I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi team, I'm using Mesh in my project. Using this thread as a reference, I tried to decrease the data throughput and experiment to see if devices could communicate with each...
hello,
i want to know if is possible have Multilink, ble Uart and relay together? it is for make an a type of Mesh network of 4 devices with a BW of 1Mbps (see the image...
Hi
I'm testing the SLM application in nRF Connect SDK ver 1.3.1 on nRF9160 PDK ver 0.8.2 using the LTE Link Monitor v3.5.0
Giving the following commands, the UART stop...
hello ,
i am working on recieving data from sensor using nrf52832 with time and data right now i am getting time that is set by me my problem is i have to set time automatically...
Here is an issue I am having when using MQTT in a poor (RSRP < 15) LTE signal environment
Condition:
nRF Connect SDK v1.3
modem firmware v1.2
TLS Socket is configured...
I've worked through the Custom BLE Service example ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ) and I'm attempting to port it to C++ to form the...
Hi,
I need to write a linker (ld) script for our nRF52 application. Essentially I need to combine the linker script that we already use with the scripts that exist in the...
trying to build a long range coded phy broadcast/scanning application. as I know zephyr doesn't support that so we have to include nordic link layer based on this post
https...
Hello all,
i am using ble_app_uart example.I add the line
in the begining of the main function. All the ble connection works, but putty shows strange characters...
I am having a bit of trouble getting high enough data throughput for my application so I have a few questions regarding it.
Can running the spi/other peripherals affect...
Hi，
I tried to build a BLE sniffer environment. And it works well to capture the LE secure connection air packet after Eable Secure Connections debug mode （uses the debug...
Hi,
using:
SDK for thread and Zigbee 4.1.0
NRF52840dk
I am trying to add UART (for my custom application) to an existing Thread example with CLI. (e.g. ble_thread_dyn_hrs_coap_srv_freertos...
Hi,
I'm really struggling with encryption, kind of lost in the woods of libraries, api's and documentation. Can anyone point me in the right direction?
Config: I have...
Hi support team,
i'm trying to build sercure bootloader on beacon nrf51822xxaa. I used SDK 12.3, here is my config
and i use nrf program to read flash infor
when...
