I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
software: nrf5_SDK_for_Mesh_v4.0.0_src
hardware:nrf52382QFAA
I just build the sdk,and then download s132_nrf52_7.0.1_softdevice.hex and light_switch_provisioner_nrf52832_xxAA_s132_7...
Moved to a new machine and now can't debug. I suppose I've overlooked something. First, Segger doesn't recognize that it has just compiled the app and asks to recompile. Then...
I've been looking at ways of implementing Web Bluetooth to connect to a Thingy52 using Bluetooth Low Energy.
https://github.com/NordicPlayground/Nordic-Thingy52-Thingyjs...
Hello; I have been working with nrf52840 dk's for the past couple months, and came across a few questions.
First off, my temporary goal using nrf52840 is to send a timestamp...
Hi
I am planning to use the nRF52833 for the AoA direction finding application. On that I had two questions.
1. Currently I have two nRF52833 DKs for transmission and...
Hi all,
I am developing on nRF Mesh SDK 4.0.0 with nRF52833 DK (PCA10100).
To save/restore persistent model state to flash, I added the code using mesh_config_entry_get...
Hello,
I'm new with the nordic chips and SDK and have a short question: I'm trying to send the battery capacity of my BLE device within the advertising data. I found some...
Hi
Do you have any example code to support OCF standard and/or IoTivity (Lite).
Or any plan to support IoTivity?
(We're targeting OCF supported device with nRF52832...
Hello all,
I am running "ble_app_beacon" example code in nrf52832. when i'm using samsung and honor mobile phones the nrf Connect application is not showing the beacon,...
I'm trying to enable the CMSIS Wizard on SES 4.42a. I followed the instructions and pasted the required xml into tools.xml, saved the file and restarted SES.
This is my...
Hi Support,
I need to use another eSIM not the iBasis, because the company those not have roaming coverage in Bulgaria.
Question: If I use a IoT eSIM card Telefonica...
I want to send a one byte payload from the nrf24l01+ (Sparkfun dev board), to nrf52840 DK using the example esb_prx. How should I configure the nrf24 registers to make this...
We have run the Hello World program on the nRF5340-PDK, but now following the basic steps to program the heart rate example, there is no BT broadcast for Zephyr Heartrate...
