Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
Hi,
After sending a few textmessages from the client to a server (8 bytes long approx. 10 messages/sec) i get a mesh assert on the client sometimes:
0> <t: 205648>, app_error_weak...
Hi, I'm using a PCA10056 DK board to start new development. I try to program DFU secure bootloader and SoftDevice using nRF Connect 3.0.0 My issue: - configure both hex files...
Hi All
I am recently working on CSAs (Channel Selection Algorithms) in BLE on nRF52840DK, and I am using Zephyr to develop them. I have 3 nRF52840DK, one as sniffer, the...
Hello, I've developed a BLE Mesh Network using the NRF MESH 3.1.0 SDK and the nR5F SDK 15.2.0. My network has 1 client node and max 63 server nodes: I'm using the generic...
I've been developing a solution that utilizes Mesh DFU along with the Mesh Bootloader. However, I've been seeing a frequent issue where the DFU aborts prematurely due to missing...
Dear DevZone,
I'm trying to use the Seeed CAN BUS Shield V2.0 (MCP2515) with the nRF52840 DK, but the library provided is written for Arduino One.
Do you know if any already...
Hello.
I m looking for libraries wich contains functions/methods (for example how to scan, provision, adding nodes etc. ) and solution how to use them.
I found something...
I am working with nRF 52832 platform and I soldered SB12 and cut SB10 because I wanted to feed from the external power supply and with this situation I can not connect to...
I have been working with the Nrf52840, SDK15.2 and Segger Embedded Studio 4.20a using external GNU 7 2017-q4-major. The project builds without error on the original PC. I...
Hi
How to find out which BLE version is supported for a given Nordic SDK + SoftDevice.
From which version of Nordic SDK is compliant to Bluetooth 4.2 ?
Hello,
This subject is partly a conclusion and partly a question I would like confirmed.
Our scenario is that we would like to fetch flash logs over BLE, but not really...
“EBSHSN” is reset by the RESET pin when the control CPU shifts to sleep mode when the terminal device is stopped. When measuring the current consumption in this state, about...
Hi, nordic.
I've been developing a product with ws2812B.
As I know, ws2812B is needed around 5V to work well.
And I measured voltages on 52 DK board.
VDD pin has...
