I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I've tried for two days to log back into the cloud service and just get the spinning angles. I tried to create a new account and the same. I was able to change the password...
Hi all, I would like to implement a fault handler in our nRF9160 based system to handle hard faults/unhandled exceptions by resetting the system, but am having a hard time...
Dear Nordic team,
I have a running NRF52 with a firmware based on the freeRTOS demo. To this demo I added the PDM Support Module and the TWI Module.
As soon as both sensors...
We are trying to implement models inside the mesh. So we've started with a functional example of the generic on off and tried to update it according to our needs.
The custom...
Hi,
I have 3 devices that all act as broadcaster and observer they continuesly sending data to each other, now i want to establish a connection between one of those 3...
Hello,
I have 2 pieces of nRF52840 and I managed to connect each other. One is central, uploaded the code: 'nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_multilink_central...
NRF52832 DUF success but when download from segger studio, Jlink RTT viwer print NO DFU found, but when download bootloader from segger stuio, can not entry app
Dear Nordic...
Hello all.
I need to work with the RTC especially its events and interrupts, and I have some misunderstanding after read its manual.
I need to use it for low power systick...
Hello,
nRF52840-DK
SDK: 15.3.0
s140
IDE: SES
How do I maintain the persistent flash data I have using the FDS while also using DFU. I have seen several older posts...
Same as Case ID: 234629 .
Calling modem_info_short_get for the parameters MODEM_INFO_MCC and MODEM_INFO_MNC fail.
I suspect the problem is in code. Tracing the MCC call...
I've made a project that scans and advertises.
The first problem: When i have one central link, I get the problem that the client service gets events twice.
<debug> ble_db_disc...
I'm using nrf52840 SDK V15.3.0 SoftDevice S140. I want to test long range feature and 2mbps mode also . How to add these features in SDK example code like ble_app_uart or...
Hi guys, i'm playing a bit with the ble blinky peripheral example, as a precursor to a bigger project.
What im trying to do is disable the services completely, meaning that...
Hi all,
I am trying to emulate a device with ble-driver-py. What I am looking is to have a device advertise, provide few services with respective characteristics (read,...
