Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
we've just found the information about the knobattack ( https://knobattack.com/ ).
Is there any fix for this issue with the new updates?
Best regards,
Constan...
Hi,
I have recently developed a simple custom board with the use of the BL651 module to have a dev board for myself. Although the schematic diagram is simple and the PCB...
I have nRF9160-DK bought fairly recently. The IMEI is printed on a label on the back of the board. But, there is not PIN. Registering the board as an LTE device on nrfCloud...
Hey all,
I was curious to see if anyone else is seeing the same problems I have with DFU.
I'm currently running SDK 15.2 and version 1.8.8 of nRF Connect on iOS. When...
Hello,
Previously I was using nRF52 SDK V11, printf did print properly and provided linefeed with '\r\n'.
Now I started using SDK V15, printf is no longer supported and...
I'm developing a nRF52832 based HID device and I'm at a bit of a loss as to why it isn't working on iOS. The device works as a keyboard fine on macOS, and it connects and...
Running nrfjprog 10.3.0 on macOS 10.14.6 (18G87) with an nRF52 dev kit
Occurs on all 10.x releases of Nordic command line tools. Other switches such as -i work.
edit...
Hi, I installed the nRF connect SDK, but get the following problem when trying to open the asset tracker project:
If I press ok, I see this:
Any ideas about what...
I use nrf52832.
Document written,
-------------------------------------------------------------------- RX current comsumption is IRADIO_RX0 Radio RX@1Mb/s BluetoothLowEnergymode...
Hello,
I'm trying to use raspberry pi to program nRF52832 on mass production. Because it's easy to do some test job with raspberry pi.
But there are still some issue I...
I want to achieve: 1. Mobile application networking with multi-lamp mesh 2. After mesh networking, many smartphones control all lights independently through proxy nodes. I...
Hi,
We are using nRF52832 based module on which we are using HCI over UART functionality with the help of Zephyr(v1.14.0) SDK to find the nearby beacons via Bluez stack...
Hello there,
So we are working with a sensor that needs to receive a pulsed voltage, so we are using a PWM signal from our nrf51-DK applied to a transistor based circuit...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the nRF5 SDK v15.3.0 and modified twi_sensor_pca10056 program...
