Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
I want to load both "SPM" and "http_update_ota" code separately to the nRF9160.
For that as suggested in " http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.4...
I've been trying to configure a second UART for use on the nRF9160 DK. However, I'm having some issues getting anything to send over the UART. I feel like I'm missing something...
Hi,
I use the nrfx_rtc_tick_enable() function to enable tick interrupts for the RTC.
I have a statemachine that in some states disable the interrupt and sometime enables...
Hi everyone !
I want to use serial communication with my ble project. So i tried to implement "/example/peripheral/serial " project into my ble project. I encountered too...
im using Feather EVM. im using the app_ble_uart . after i added SPI to the project i dont get any errors but the code does not run (goes to main) and when i press run it goes...
With an Objective to test mulitple DUTs that provides BLE4.2 data, We are in process of procuring the nRF52840 Dongle.
I would like to understand if i will be able to do...
I successfully installed the NRF9160 DK toolchain on my linux desktop the other day using the "Getting Started Assistant" App, but when attempting to install the same toolchain...
Hi!
I'm currently evaluating Thread using a few nRF52840 DKs.
The network will be used to gather and provide sensor values.
For various reasons, I want to avoid using...
Dear all,
I have two nRF52 Preview DK boards with the SoC nRF52840. I am testing the light switch example on both boards. I have changed the light_switch_server, such that...
I tried some steps and falling back to support. I received my custom nRF52832 board and wanted to kickoff programming the board to meet my requirements. I used nRF52840 DK...
Okay, this is a fairly involved issue, so I will try to simplify as best as I can.
In short, my new Ipad Mini 5 cannot connect to an NRF52840 running the NUS peripheral...
I have just purchased 2 pcs. nRF52840 - one of them works fine - the other one reports this when i run dmesg on my linux (tested on 2 different systems) "Cannot enable. Maybe...
Hi,
I'm using nRF52832-CIAA.
VDD,Pin A7, tide with Cap 4.7uF 0603
VDD Pin H7 tide with Cap 100nF 0201
DEC3 100pF 0201
DEC2 100pF 0201
DEC4 1uF 0402
Using LDO...
