Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear Nordic,
I want to achieve long range in my custom board
I have some doubts:-
1. is it any difference in schematic for achieving?
2. Which HF crystal i used...
Hello, I was wondering how can I send data continuously over NUS.
I am using the ble app_uart and app_uart_c to program two NRF52382 with s132. My goal is to sample a signal...
Hi
SDK 15.2.0 ch_map[5] is 5 bytes long so 40 bits. Can you please confirm if ....
ch_map[0] bit 0 corresponds to channel 0
ch_map[0] bit 7 corresponds to channel 7...
the Product Specification v1.4 of the nRF52832 SoC. On page 23 the RAM0 block section 1 address is given as 0x21001000. From the context I believe, this should instead read...
Development Kit - nrf52 DK
SDK - 15.0.0
Computer Platform - Windows 7 - 64 Bit
My application was working fine until I decided to change the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello everyone!
I have a question regarding where should I place NRF_DFU_SINGLE_BANK_APP_UPDATES flag. Should it be inside sdk_config.h in a bootloader or application? Or...
How to enable and disable FreeRTOS tickless idle(RTC or Systick)? Anyway to wakeup from tickless idle mode when there is BLE activities detected?
Setup:
1. nRF5_SDK_15...
Compiled Blinky client fails on Dongle PCA10059.
Precompiled version nRF5_SDK_15.2.0_9412b96/examples/ble_peripheral/ble_app_blinky/hex/ble_app_blinky_pca10059_s140.hex...
I am trying to compare a bunch of BLE mesh options and I am trying to evaluate the software stack for nRF mesh
Whilst trying out the light switch proxy example, I noticed...
Hi Great Nordic Team:
I have some questions about nrf24ap2 reference schematic, please kindly help to give me some tips.
※it's reference circuit of Synchronous (bit...
Hi Sir,
As reference below link, and we can find the Tickless IDLE enabled ~700uA in SDK 15.2
https://devzone.nordicsemi.com/f/nordic-q-a/24733/nrf52840-sdk-14-0-0-and...
Hi again!
I'm trying to send/receive data between an nRF51(master) and a AVR/HM-11(serial/BLE module)(peripheral)
After following this visualgdb.com/.../ tutorial based...
Under some conditions I want to force advertising to transition from slow to fast. With SDK 14, I could just call ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST)...
Earlier for nrf52 we could filter out connections on the peripheral based on rssi, need similar operation for nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_uart...
Dear Nordic,
I have one nrf52840 dongle.I want to know which polarization of antenna (PCB antenna) gets maximum range?
another thing i want to know what is the maximum...
