I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, everyone.
I've developed a custom board using nrf52832. I tested it and found that CPU core, GPIO and other peripherals work well, but BLE doesn't work at all.
I ran...
Hi,
Raspberry (SPI Master) -> NRF52832 (SPI Slave)
The code below execute event_handler of SPI with NRF_DRV_SPIS_XFER_DONE type. But RX buffer is empty. All bytes are...
Greetings,
I'm in the process of choosing a nRF52 module. I know of this link for the various modules www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules.
I...
Hello, I've been trying to get directed advertising and auto-connection working on an NRF51822 peripheral.
I'm using SDK V11.0 with SD130 v2.0.1
This is the scenario...
Hi,
I used the code ble_app_uart_c on board 10028 as a base for my custom board.
My board is nrf51822 QFAA based so I changed all occurances of nrf51422 to nrf51822...
Hello,
We are trying to communicate to this board ( www.adafruit.com/.../1697 ) that has nRF8001 at its core.
Unfortunately, our TX is only able to output BLE 4.2
...
I'm running on nRF51822, SDK 8 (not totally sure, I inherited the project), SD130 and mbed.
I've tried and failed with my own code to use pstorage.
I'm now trying a...
Hi. I'm using nRF51822AC, SDK12.2.0, S130.
The size of "s130_nrf51_2.0.1_softdevice.hex" in SDK is almost 300KB.
But chip's flash mem size is just 256KB. It's bigger than...
How is it used? And why to use it?
static nrf_saadc_value_t m_buffer_pool[2][SAMPLES_IN_BUFFER];
instead of
static nrf_saadc_value_t m_buffer[SAMPLES_IN_BUFFER];
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
Hello,
I tried to flash an application to the nRF52832. First I flashed the softdevice, after that I flashed the bootloader and next the application.
The application...
We were doing various tests using PCA10040.
Then suddenly I can not connect to the PCA10040 board.
In the boot loader mode of PCA10040 board, connection is made.
What is...
