Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
SDK:8.1.0
Chip:51822AAHO
Hi,i use the nRF51822-PSV3.1 Schematic diagram.The chip set 4dbm tx power,
then i test the test point(C6) as follow,2402MHZ and 2426 MHZmax...
Hi,
I run the HID keyboad example, and a problem confuses me. I use the "lightblue" APP to connect the peripheral--"Nordic Keyboard", but the iphone appears a pairing box...
Hello!
I have been working recently with the PCA20006 Beacon board. The example we have tested is the ble_app_beacon that allow us to change the UUID/Major/Minor and go...
This may be a stupid question, but...
What value is BLE_GATTS_ATTR_LENS_MAX
Its mentioned a lot in the SDK, but I can't actually find a value for it actually defined...
I would like to know how to add Service Change UUID: 0x2A05 Properties: INDICATE Descriptors Client Characteristic Config UUID: 0x2902 to Generic Attribute of Nordic_HRM....
Hi - I am trying to send a signed 16bit Integer from nRF52 to iOS. Using the following characteristic reader from Nordic in the nRF Toolbox on Github (here) .
static func...
Hi there:
I found a strange phonomenon about consumption betweeen advtisement and gpio17 of 51822.
When I start ble adv while setting gpio17 to input disconnected mode with...
Hi, possibly a bit of a stupid question but here we go:
I'm developing a prototype system, which includes my own design of sensor modules that transmit their data via nrf24l01...
Hi, Nordic
I know when I program one BLE app, softdevice should be needed.
If I program esb/gazell app, softdevice is not needed.
I want to know, when I program one...
Hi, Nordic
I want to add BLE DFU service in my own app, so that the nRF52 can operate BLE DFU.
I only modify 2 places:
static void services_init(void) --> init ble_dfu_init_t...
Hi，Nordic
I am working for BLE_DFU, on SDK 12.1 and SoftDevice s132.
I checked, I should add below code in ble_dfu.c
char_md.char_props.write = 1;
Then I added...
Hi, Nordic
I check SDK13.0 bootloader_secure sample, it do not work
nrfjprog download bootloader_secure
use nRF Connect app in Android mobile phone to...
Howdy!
I have to admit that after about 2 weekes of fight i finally made some progress with NRF51. Afterall i can upload my own program to chip so it changes leds on NRF51...
I get an error when trying to pair to a peripheral in nRF connect v1.0 on Linux.
I have two nRF-DK v1.1.0 (pca10040), one is the adapter that is connected to nRF Connect...
