I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi Guys,
Is there a way with the Keil C Compiler to get an *.LST file or some sort of Assembly output from C source input?
I'm still trying to write some code to drive...
Hi
Now, I am coding SDK5.0.0 keyboard project and almost done. It's Keil C version. Did you have IAR version for reference? Besides, did you know if IAR supports J-Link lite...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I would like to know how to implement reset button on nRF51822. Image of schematic would be very useful, but good explanation should be enough. Thank you in advance.
I...
Hello,
I am trying to build the nrf51822/Board/pca10001/s110/ble_app_proximity project, with gcc ...
I have created a makefile based on the button_radio_example makefile...
I would like to know if the Notification/Indication of a Characteristic is enabled. I suppose this data is stored in a CCCD on the stack. I have not found any SVC instruction...
It seems the only way to use the S310 alpha hex on the development kit is to replace the IC on either of these boards; is this correct or is there another way?
Also, the...
Hi,
I am researching BLE product for a similar task (1 central node with 4-6 concurrent slaves). I have looked up other vendors (TI, CSR etc) and come to a conclusion...
After Googling and searching this forum I still don't know if I can make an HID peripheral (a touchpad) for Android that operates over Bluetooth Low Energy, and is accepted...
Over the air downloaded updates are an essential feature for productization. Are there any examples showing how to implement the OAD? Also is it possible to OAD update the...
Hi,
My nRF51822 evaluation board is not working, here i attached the screen shot's of the error messages i used to get on both the nrfgo studio and in keil. Please suggest...
Hi
When I reduce the operating voltage, the nRF51822 with the heart rate demo running resets whenever the voltage drops below 2.1V and does not recover unless I increase...
I need an star network with 1 master and 4 to 8 slaves. I'm not so concerned about the power, but the convenience of the nRF51822 is attractive.
Does the current BLE library...
Dear all:
Now,i have issue ,i can't fund device.(i have sure the hardware is OK)
i think it is program overwrite the J-TAG register(TDO)? but i may not sure.
have any experience...
The Arduino SDK by David Edwin linked to here is no longer available since the Bluetooth forum seems to be down, and has been for some time: devzone.nordicsemi.com/arduino...
