Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi there,
Please let us ask about SMP server sample. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr/README.html#smp...
Hello All.
We are planning to do a EMC test on our device that is using nRF52832, the test facility requires us to provide a programming interface that can change the...
Hi!
Can't continue here:
https://devzone.nordicsemi.com/f/nordic-q-a/56211/bootloader-difference-and-implementation-from-sdk-14-to-sdk-16
So I've made a new question...
Hi
So I tried to use the lwm2m sample client (nrf\samples\nrf9160\lwm2m_client) for FOTA upgrades. I do get a connection to my plattform. When I start the update I do get...
I'm trying to figure out how to change the start address of my application when chip has a bootloader flashed on it.
For example :
Bootloader address = 0x0
Main application...
Hi,
Fairly new to the world of nrf development and C programming so apologies for the potential newbie question.
I am looking at how I can setup a Raspberry Pi 4 as...
I have an application that uses the nRF52840 for BLE in central mode. This application is battery powered. Basically, the device is listening for beacons and logging which...
I'm trying to connect to a device with a public address using an address filter in the scan (not whitelisting), I've seen plenty of similar unresolved issues posted here....
I am searching for the zip with reference designs and PARTNUMBERS for the nrf52 series. The datasheet link is broken and I can not find the ZIP file in the new Help Center...
Hi,
I'm trying to use the serial number of the nrf52832 microcontroller in code, how can I acess it with Segger.
I tried using this code from this link but it doesn't...
Hello. We are planning to change from QFN48 to WLCSP package in our product. However I could't find any guidelines to create the library for Eagle. I was wondering what is...
Goodmorning,
we are trying to update the firmware on a nRF24 development kit board (nRF2727) that was programmed with the PTX sample from your software development kit....
Is there a document comparing the differences between the softdevices for the 51832 ?
I have been looking at the data sheets, but its too much to grock on my own.
Thank...
SDK: 15.2 IDE: Keil SoftDevice: 6.1.1 Board: Custom Hello, I would like to synchronize an SAADC reading during a BLE transmit event. The power source to my board is a CR2032...
Hi,
I am developing an application for Thingy:91 in which I want to send data from the device to MQTT server. I am using 1.1.1 modem firmware and 1.2.0 ncs tag.
The whole...
