Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hello!
I have been working on a code using ble_app_blinky and try to insert whitelist on it using ble_app_hids_keyboard as reference. After the APP_ERROR_CHECK i get a NRF_BREAKPOINT_COND...
Hi,
I am connecting nrf52832 to a windows computer, and it connects to it, but after a while (30 seconds), it disconnects automatically. When i try to debug it, i see a...
Hi,
the nRF5 SDK v13.0.0-1.alpha uses the BLE_GAP_PHY_CODED constant to indicate a coded PHY.
The BLE 5.0 standard specifies two options for coding: S=2 (500 kbit/s...
My app (SDK12.3.0 + S130 v2.0.1) is being prevented from advertising because flash_access_in_progress() is true (m_queue.count != 0) on ble_advertising_start (ble_advertising...
Hi! I'm trying to add the nRF drv_timer library to the ble_app_template example project (BLE Peripheral).
I have added the nrf_drv_timer.c file to the project, and the directory...
I need to switch between 3 central devices (device slots, rather) with a peer manager and SDK 12.3.0 (nrf51822-based keyboard, see sdk12_3 branch for a peer manager https...
Hi,
I have a problem, like this fellow engineer here , but the solution is not applying for me.
Our firmware support different modes of operations. Mode changes are...
Hi,
I was testing out the nrf52840, and i wanted to initialize the BNO_080 sensor with the nrf52840 DK. Now, i realized that if i want to read from registers to get the...
Hi, I'm using nRF52840-DK , SDK 15.0, buttonless DFU sample + secure bootloader I see that resuming DFU works only after disconnect, but no longer on sw reset or power down...
Hello
I have seen in the various examples that most of the time the output are digital (0 or 1) . i program a PWM signal to make any DC output on the pin 18
but unfortunately...
I am developing a windows deskop application for BLE devices.
which laungage is the prefered for this type of Desktop application having predefined libraries..
Nordic...
We have an application running on a custom board with the following configuration:
nrf52832
SDK v12.3
Softdevice S132 v3.1.0 and S332 v2.0.0 (different variants of PCB...
Hi, I am using nRF51822 now,SDK11.0, how to let the peripheral open the peer's notification, My original design uses DA14580, Android APP can receive messages when the peer...
hello .
i am trying to open driver in the advertising.py example pc-ble-driver-py-master
driver.open() and this line throw exception
if err_code != expected: raise NordicSemiException...
It seems nordic devices can not be programmed without certain segger software.
In order to set up my toolchain, I had to install SEGGER Embedded Studio IDE (although i dont...
