Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Using SDK14.2.
I'm trying to optimize the throughput of my ble_nus-based app (I'm getting about 5k/sec right now). I've read elsewhere on this forum that increasing NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hi.
I am trying to program the ble beacon application example that requires the S132 softdevice. I am following the instructions that request the device be erased first...
Hi,
I'm looking for feedback on the feasibility of using Bluetooth Mesh to network Bluetooth modules in a series of adjacent hotel rooms. All the nodes are also relays since...
Hi!
I have a Nordic nrf51822-DK. I'm need send large data to the Android phone (10 mb).
I'm use sample devzone.nordicsemi.com/.../dealing-large-data-packet-s-through-ble...
This may not be the place to ask this question but have to start somewhere.
1. Using an Adafuit BLE Sniffer nRF51822.
2. Ble-sniffer-osx, Version 1.2. 4 (build 28)
3...
According to the answer here , Nordic currently doesn't offer a proxy node implementation.
What would be the best way of getting started to create a proxy node? Are there...
Hi,
My device is peripheral and server and is connected to an (android) phone. I have two related questions:
a) I understand that maximal packet size is obtained by calling...
Hi!
I'm trying to log the flow of communication in the Light Control example of the Mesh SDK. But when I log all the received network messages on a server, I also get a...
Hello
I would like to check coded phy performance
in order to do so I need to achive the following:
1. change to coded phy on default (as I ub\nderstand can by...
I am getting BLE working on an nRF52832, and I am a bit confused as to what I should be setting RADIO->CRCINIT to. I was hoping someone could clear this up, which is more...
Hello
I m trying to measure the current in my development card nrf52DK using the power profiler kits, so i prepared the board by (cut the PCB track shorting solder bridge...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0. The app is based on on the ble_app_template PCA10040e S112 (The final chip will be a NRF52810 that's why...
I want to flash the program in my custom board. I have flash the program in nrf52832 BLE module via j-link using nrf52832 development board. So, how do i confirm that the...
I use the SDK S110, I hopes in the low power(operation the current 100 uA is following), and then sustains every second bluetooth broadcast and every second computing time...
Hello,
I am using sdk 12.2.2 and customised nrf52 board.
My challenge is when I am using sofdevice + app hex file my device takes 4.1 uA current but when I am uploading...
