Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Dear sir/madame
In our project we want to implement MAX17260 battery fuel gauge to monitor the battery status in the handheld device.
The interface towards MAX17260 is...
I'm trying to run the HID composite example on a nRF52840 dongle, and its not working:
- I refer to : nRF5_SDK_17.0.2_d674dde\examples\peripheral\usbd_hid_composite\pca10056...
Looks like 2 mistake in the latest nRF9160 production specification:
1: 1Mbps but 1200 in description section.
2: Power consumption could be in uA instead of mA.
Hello,
Sorry for the basic question, but I am trying to customize an application basing on the ble_app_cgms example.
In the debugger terminal on SES I am receiving the...
Hello,
I am currently working on an IIoT product using Zephyr and NRF SDK v1.5.1-2-g76c027893 on the NRF9160 and a WFM200 wifi chip. For this project we are using Civetweb...
Hi
I'm locking for an example like zephyr\samples\boards\nrf\system_off for nRF9160 DK
zephyr\samples\boards\nrf\system_off uses nRF51 DK or nRF52 DK board for the demo...
Dear support team,
I would like to use GPIO 09/10 as a GPIO interrupt.
I just searched and I see that need to define CONFIG_NFCT_PINS_AS_GPIOS.
But I can't do it. Please...
Hello, I'm making a system with NUS of nRF52832 and nRF52840 to sample data with SAADC. I started the system with "ble_app_uart__saadc_timer_driven__scan_mode_03" from Github...
Hello!
There is a sample simple_mqtt which is written for nrf9160 DK. Is it possible to make app_signed.hex file to load in thingy 91.
I tried to change prj.conf and have...
Hi,
Using the HRS peripheral example provided in SDK17 with S140 7.2.0, I am in the process of migrating to a custom board using nRF52833. I have already made some changes...
Hi,
Can you please tell me if Segger compiler initializes all variables to default values?
If so - can you please send me a link to that content?
Thanks
Hello,
My nRF52840 board is connected with SPI flash over SPI. I have configured the nordic as master and my SPI flash is slave as mentioned below:
Using the internal...
Hi,
I have a nRF52840 USB Dongle that I am using to perform OTA DFU to use to perform OTA DFU.
After the update is finished, the device keeps running the code instruction...
hi
I have written a driver for an SPI sensor, and it works perfect in a nrfx_spim example project.
But when I tried to add this driver to a ble custom project, errors...
