I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am using Nordic board to drive an accelarator. There is already an exist project and it can run successfully. I want to combine this project to a new project and it has...
Can I use the nrf52810 internal temperature sensor to measure ambient temperature? I know it is designed for die temperature but I don't need to know the accurate temperature...
Hello,
From my understanding, I should integrate the LwM2M Carrier Library connection as the first step in the boot process and once I have received the LWM2M_CARRIER_EVENT_READY...
Hi Team,
If we send 20 bytes of data to AES-ECB 128 bit (CC310/ mbed TLS) Crypto engines for Encryption/Decryption due to bytes padding, how many bytes it will become...
With iOS and Android smartphones we are advertising some ble frames.
With our own code on the nrf 52840 we get around 2-4 advertisements each seconds on the nrf 52840 chip...
Hello,
I am trying to use the peer manager on a nRF52832 acting as a peripheral with both bonding and legacy pairing on SDK 16.0.0.
The application configured with bonding...
I am using version 4.1 of the Mesh SDK and version 16.0.0 of the nRF5 SDK on Windows. I was able to successfully generate the ninja build files using CMake. However, when...
Hi,
I'm interested in multiprocol examples and I'm trying to compile examples provided by the latest sdk for nrf52840 mcu.
IAR 8.x doesn't work I have this error "code...
I have written two functions to write and read data from the flash using flash_fds module. In this way I am calling the function to write the data to flash :
fds_write_record...
Hi there,
I was comparing the power consumption of ble_app_hrs_freertos and ble_app_hrs examples on nRF52840 DK. The average VDD current is 7.4 mA for the example running...
Hello,
I'm in need of turning on and off the LTE link to use the GPS in cases where I can't depend on PSM. The LTE Link Controller library is good for this however I have...
I'm in trouble... My design has 3 SPI devices, and at a late stage I ran out of GPIO so I added a I2C I/O expander before spinning and building my PCB without thinking too...
I'm trying to use nRF sniffer 3 and can't get it to detect the dev kit on Windows or mac. I've installed it into wireshark and see the toolbar, but no interfaces are listed...
Hi,
Can we give a voltage more than VDD+0.3V on an open drain high impedance configured IO pin? By open drain, I mean:
nrf_gpio_cfg(pin_num, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
