Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi.
I'm using nRF52840 Developement Kit and my environment are below.
OS : windows 10
SDK version : 16.0.0
Tool : nRF Connect (with DTM,Programmer app) / Seger embedded...
Hello everybody,
I'm trying to flash an example code (let's say the blinky one) from the SDK (15.3) onto the Arduino Nano 33 BLE board.
I know that is possible to flash...
Hello,
I'm trying to resolve an issue in my project.
It appears there is a memory leak.
In logs I can find the error code : 0xBFED
Do you know what that code is? ...
Hi,
I recently had a problem about timestamp that it's all 0 on the RTT Viewer.
And i 'm based on the nRF5_SDK_15.2.0\examples\peripheral\rtc to check the timesteamp....
Hi Nordic
I have some issue When using NRF52832 central to connect the NRF52832 peripheral.
i am following the SDK15.3.0 ble_app_uart & ble_app_uart_c to deign the central...
Hi
I have a question about LXFO input on external low swing clock setting using nRF52832.
I can see the input specification of external low swing clock about only peak...
Hi,
I am currently developing a stationary BLE device. I am testing the nRF52840-dongle in combination with the pc-ble-driver. For that purpose, I am using the connectivity_4...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am operating in a "peripheral" configuration, with bonding enabled. "BLE_GATTS_EVT_WRITE" occurs when notification is permitted...
We're porting over some software to the Arduino Nano 33 BLE Sense. This board comes with an nRF52840 clocked at a max. of 64MHz. However, the same code runs about 2x slower...
I want to send Tx power in advertisement packet.
Currently I am using following code.
int8_t txpower_level;
static ble_advertising_init_t init =
{
....
Customers use nrf52810 flash program to store data, but want to know what flash start and end address can be written, please point out that you can refer to that document...
Dear Nordic Semiconductor
I am using device:
NRF51802 bluetooth 4.0
Product Introduction:
Features:
1.Adopt NRF51802 bluetooth 4.0 BLE SOC
2.ARM CORTEX-M0
3...
Hi , I use the pc-ble-driver to developer desktop tools, like nRF Connect. Unfortunately, I don't know Java. I‘ve tried to used examples that work(heart_rate_collector and...
Hello,
We use a custom interface board to program and run test programs on our series of tiny BLE modules based on nRF52xxx series (ISP1507, ISP1807, ISP1907).
Our interface...
