Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I would like to store a simple integer value in the flash write and read after some event. I'm using the mesh example Dimming examples (experimental) in the nRF5 SDK for Mesh...
Hi All,
In nRFMesh app we can see the list of names of available Bluetooth devices. Is it possible to see the list of names of available Bluetooth devices using static provisioner...
According to the spec, this is how a bonded reconnect should work:
On first pass, the central client does discovery and enables descriptors to characteristics of interest...
Hi,
I've got an application based off the asset tracker firmware that needs a UART. From the many threads on the topic, I've found a way to shut down the UARTs to save power...
Hi,
I tried out the light client example in the Mesh SDK V4.0.0 and it works so far. Now
I added more data in the messages and it works, but only as long as the message...
Hello all,
I have a pretty simple question that I hope can be answered for me. I'm integrating an nrf52832 development kit (PCA10040) BLE sniffer into a test fixture to...
hi,
i able to write and read unsigned integer value from the flash, but when i try to write some string to it ,the device is not responding.
void Reading_the_data_from_flash...
Hello Sir,
I would like to ask about the handling of the interruption in the nRF52 SDK.
The versions for SDK and SoftDevice are 15.3.0 and S132 v6.1.1
In the processing...
Hi all,
I am using a nRF52840 with SDK v16.0 on SES. I am trying to understand the flow of code in the secure Booloader(/SDK_v16\examples\dfu\secure_bootloader\pca10056_s140_ble...
Hi ,
I am trying to interface sg90 toy servo with NRF52840 , I am using nrf library but dont know how to drive it from 0 degree to 90 degree to 180 degree . May I know the...
Hi
I m using NRF52832 for beacon application.In my application, the device should be in the system off mode .After holding button for 5 secs, the system will back to idle...
Hi
I'm using SDK version15.2 and SD on a custom board based on nRF52840.
The board has two serial ports, and I want to use both independently. Using the Serial Port Library...
Hi Nordic Team,
My requirement is-
Advertise -> Connect to 1 device -> Send packet -> Disconnect -> Delay(1min) -> Advertise -> Connect to 2 device...
I am using Timer...
I am using nrfMeshProvision cocoapod to create a Mesh Network using a iOS Mobile application. In first step of identifying the device, i am able to call bearer.open() and...
