Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Dear all,
I am trying to work with FOTA. I am able to run successfully the http_application_update.
But now, I want the device to download a custom firmware that I...
Hi all,
I am trying to set up UART communication on the nrf9160. I am using the nrf9160 DK and zephyr.
I have selected device UART_1 and after I cal functions device get_binding...
Hi,
I am trying to implement OTA updates on iOS. Where can I find out what error 10 means?
Below is the log of events from my app. Please don't hesitate with questions...
Hello guys,
I have nRF52840-based BL654 SoC module on my custom board and I develop the firmware in SDK 15.0.0 environment with s140 SoftDevice.
Among other things, I...
One little example At the bottom of file nrf5SDKforMeshv310/bin/ospace/examples/dfu/dfu_nrf52840_xxAA_s140_6.1.0.hex
We can make it more human-readable by utility from...
Hello,
I'm trying to make custom board based on Thingy 52.
First problem that I get I want to change gpio's order according to my needs.
I can't not find where in the...
Since the manual for the nRF9160 DK doesn't have a full schematic, I'm not sure what sort of power supply decoupling the nRF9160 needs. What are recommended bypass caps, if...
Hello,
I've modified(added custom libraries) an existing example project from the SDK(v 15.3), and I'm trying to build and flash it.
The project compiles fine, but throws...
Hi,
I am using nrf52840 with an ADC that senses data and sends it via bluetooth. I want it to sense data, store it in the memory and then send it via BLE and then start...
Hello,
The current project I am troubleshooting includes an NRF51822 chip. The project includes a boot loader, application hex, and soft device S110 V7.3.0. It was noticed...
When trying to install the nRF Connect app (3.1.0) on a windows 7 machine, it hung up and froze during the Jlink install. After using system restore to go back before that...
Hello we are using SDK 15.3 and SD s140 v6.1.1, we use the cryptocell to do some AES encryption as well as MAC and ECDH.
We noticed that our application was running quite...
Hi,
I'd like to test how long it takes to get a gps signal and send the nmea string via udp. Therefore I took the example 'udp_gps'.
As far as I know the program starts...
