Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
sdk15, SES, SD132 Hi I am using an SPI slave with nrf52 (master) I launch in the main() and I also initialize the SPI slave on main. I also configured an app timer and when...
[EDIT] The solution is posted in one of my replies.
I'd like to set up a programming and test station for the nRF52832. Segger JLink tools work fine in Windows, but I...
Good day Nordic,
I am starting to work over the ble_uart_central example, this is a project that uses bsp_event_handler to issue the events from buttons, but I cannot...
I am new to Nordic and i am using nRF52840 microcontroller, - SDK 15.2.0 - s140
When i program the microcontroller it gives me error message that my flash storage is full...
Hi,
I am using nRF5_SDK_15.3.0_59ac345 for nRF52840 DK. I am running the sdk example "nRF5_SDK_15.3.0_59ac345\examples\peripheral\twi_sensor" on nrf52840. When I am opened...
I'm currently trying to build and run the bluetooth mouse sample code on my nRF9160 DK, but I'm ecountering problems during the build process.
Shortly after hitting the...
I am having some trouble with sending messages using MQTT on nRF9160DK. What I ultimately want to to is read UART and send whatever I receive to an MQTT broker. When running...
I am trying to use sd_ble_gatts_hvx function to send custom data through BLE. I found out that for the data I am sending the function takes a lot of time to send data which...
My custom nRF52840 board uses the STmicro STM6601 push-button controller. To keep the nRF powered, the PSHOLD line must be kept high. I have a GPIO set as an output for that...
Hi there,
I am trying the test the robustness of a BLE use-case. This means that i have to create error scenarios and further observe and analyze how it's possible to recover...
Dear all i have a very funny situaton.
I can only send 1 byte in my service data when I increase it to two bytes it doesn't send. and says invalid parameters
When...
In the right process，like this：
but my program is ：
i lost “Sent Read By Group Type Request, GATT Primary Service Declaration, Handles: 0x0001..0xffff” .
in the...
Please kindly help to push this emergent issue!!!
We detected CLK signal using oscilloscope as picture below:
We can see that clock frequency is set to...
I have been making good use of the Power Profiler Kit with some impressive results on my nRF52 project.
I would now like to extend the testing to view an application where...
