Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Using Keil v5, ARMCC 5
Pin state equals:
Level 0 - 0x00000000 - pin low
Level3 breakpoint after read - 0x00000040
Level3 breakpoint before and stepped through -...
I am advertising a service and providing scan response data. It is not clear to me whether I should be bothering setting up the values of the ble_adv_modes_config_t structure...
Hi there,
i am very curious about what can be considered as interrupt factor in receiving the signal from beacons, so if these scenarios have been tested please provide...
I'm using the nrf52832-QFAB variant (32K RAM 256K Flash)
The part is marked as NRF52832 QFABB0 1630AC
Surprisingly, this part is happily running my application and bootloader...
Hello,
I can't find where in flash the peer manager data is stored. I'm currently working on DFU support and as part of that I want to define the memory area that should...
As per mesh_hw_resources.md (MESH_SDK/doc/introduction)
## Flash lifetime The flash hardware can withstand a limited number of write/erase cycles. As the mesh stack uses...
Hi all,
I am trying to develop the BLE Heart Rate Collector example on the nrF51 Development Kit. As far as I read in the Nordic web ( http://infocenter.nordicsemi.com/index...
I'm trying develop on a custom board based on the nRF52832 and am running into some issues. When I run the blinky application (with no SD) the application executes fine. However...
Hi I'm developing beacon firmware using ble_app_beacon example code.
I was able to send good beacon data for my purpose. For the next step, I want to turn on the LED which...
Hi,
I am using a custom board based on nRF52 (nRF52832-QFAB-R) and programing it with softdevice.hex and "ble_hid_mouse" example application in the nRF5 SDK v14.2.0. the...
Hi,
I am using softdevice S132 V2.0 for nrf52832 controller.I am using BLE UART app. It is working fine on eval board.But when i checked it on custom board developed by...
Hello,
I am using sdk12.2.2 and nrf52. I have implemented fds_read, fds_write, fds_delete and its working as expected. Now when I am trying to use fds_update my data is...
We are trying \Nordic\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I want to control UART. If device is not in use i want to...
