Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
How does the Tx power impact the scanning and connection with a peripheral?
In detail, say if the peripheral can advertise at a Tx power of 4, 0 or -4 dB, then will it...
Hello, dear Nordic employee,
MCU: 51822QFACA1
The using SDK is : SDK 7.2.0
The using SD is : s110_nrf51822_7.3.0_softdevice
There was one device (our product) runing...
Hi,
I am using "nrf5 sdk v11.0" example "ble_ancs_c" for nrf52_DK(PCA10040) .
when i connect to the nrf_device from ios device i am able to pair and connect to ancs client...
Hi,
I'm using the example nRF5_SDK_11/examples/ble_peripheral/ble_app_uart witn a pc10028 board. The central is done on a linux machine with a python program under bluepy...
Hi,
We would like to use the nRF52 in the following way:
BLE communication via S132
button / IRQ to wakeup nRF52 application
put nRF52 to sleep after BLE communication...
As we known,RSSI means Received Signal Strength Indicator,TXPOWER decide the power of output port.How do the two factors combine affect the device work?
Hi I spent a few days on trying to setup a thread external commissioner using Nordic nRF52840 and RaspPi 3 as a border router.
First I realized that border router implementation...
Hi
I'm having major problems implementing current time service client (cts_c). I've run ble_app_cts_c on my device and it works fine. I copied the relevant parts of the...
Bluetooth SIG recently released BLE Mesh standard 1.0. Is nordic mesh compatible with the new released SIG standard?
If not when is it planning to release a SIG compatible...
Hello,
I did used nrf_drv_spis.c (SDK SPI Slave) with nrf_drv_spi.c (SDK SPI Master). And I notice that both module configure SPI MISO line as input without any pull (neither...
Hello,
I am using nrf52832 DK and I would like to use the GPIOs port to debug a couple of signals that I genereate within the MCU.
So far I have configured my GPIOTE...
Dear experts,
I've been playing around with Thread since nRF5 SDK for Thread v0.8.0, cloud_coap_client.
I use your Border Router example with NCP example running on nRF52840_Preview_DevKit...
Hi:
I got an 0x04 no mem error with sd_ble_enable.
But my hardware worked just fine before, so after some tussle I found out that the sd_ble_enable of my working program...
how to set the ble stack ,let the sd_ble_gatts_hvx() send data return more fast,now from i use sd_ble_gatts_hvx() to get the return (BLE_TX_COMPLETE) needed 300ms.
