I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
When I connect to my firmware after cycling Bluetooth on iOS, I am able to subscribe to my Characteristic Indications without any issues. The nRF connect app receives all...
I have two boards, one is official demo board, the other I make PCB board.
I down the open-mesh source code form github.sdk version is 8.1,open mesh stack version is 0...
Hi,
I have to send data with notification from central to peripheral, because I need save some data in peripheral device.
What I have to do ?
I test it on Adnroid 4.4 ...
Hi Sir,
I am working on nRF52832 board with pca10036 cortex M4, and i worked out spi master and slave example code on a same board and configuring spi instance 0 as master...
when using secureDFU with sdk12.2, only changed the mac address.
my application is more than 60KByte,
when i test the firmware for two files, one is 62K and an other is...
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I made a BLE peripheral (nRF52 + SDK11.0.0 + s132) and have so far been using Android devices (that supports 7.5ms connection events) to connect to it. I want to connect to...
Hello,
We are sharing SPI and we found possible bug in nrf_drv_spi....
The problem was that first SPI is using blocking SPI thus does not use ISR and set it to NULL: ...
Hi, Nordic
I want to add ble_dfu service in my app, my own app will add my custom ble service.
So in service_init() function, ble_dfu_init first callback, then my own...
Hi,
I want to control a g-sensor by nRF52832 via i2c.
I am using an example( nRF5_SDK_12.2.0\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm4)
and I add the app_twi...
Hi,
I use the SAADC to sample 2 pins. I use the nrf_drv_saadc, and a timer to call the sample task.
I was trying out several gains for SAADC and I noticed that for gains...
i have a minor issue with my eclipse setup.
in the BLE_Peripheral_HTS example eclipse can't find the NRF_CLOCK_LFCLKSRC reference. codeline 604 in the main.c
Im using...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
